Anyone have Lt1 SDCE installation instructions??
Thread Starter
11 Second Club
iTrader: (8)
Joined: Oct 2004
Posts: 430
Likes: 0
From: Jacksonville, NC
Anyone have Lt1 SDCE installation instructions?? Hell even LS1 would prolly be close enough for me to figure this out. I pm'd Wendy but Im working on it now and doubt Ill get an answer tonight
i had to figure mine out also. one of the bracket stifiners mounts across the bottom of the charger straight over to the block and the other bolts at the 1-2 o'clock position on the charger housing and runs to the nearest header bolt. once you have it bolted up it is a little difficult to bring the tensioner pulley around and hold it. might need to fab a special tool to pry it around. once tentioned were you want it torque it to 70 ft lb. i can get you pics if that would help.
Thread Starter
11 Second Club
iTrader: (8)
Joined: Oct 2004
Posts: 430
Likes: 0
From: Jacksonville, NC
From your description, I still have an extra piece. It's a square piece of aluminum that is about 1 x 1 x 10 or so and it has a 45 degree angle cut on one end and is square on the other. It also has two holes cut into one end with no threads and a hole cut through the other end but this one has threads. Thats the piece that really killing me. Plus I still have 3 bolts and one has a spacer of some kind that I need to figure out where they go. Thanks for your help and yes pics would be great
that piece is mounted to the charger on the far driver side and you should have a rod that bolts to it and runs to the header bolt. you take out the original bolts in the face of the blower and use the longer supplied bolts to mount that bracket. i will send you some pics.
Last edited by Z28&WS6; May 16, 2006 at 06:41 PM.
Originally Posted by T/A KID
Man I will have my SDCE setup for my car in a week or so, I can see if I can post up some instructions for ya as well.
Z28&WS6 I am pretty close to you, what does your setup consist of.
Z28&WS6 I am pretty close to you, what does your setup consist of.
Trending Topics
Thread Starter
11 Second Club
iTrader: (8)
Joined: Oct 2004
Posts: 430
Likes: 0
From: Jacksonville, NC
Well since I still cant seem to get ahold of SDCE can someone take a look at these pics and let me know if I have it installed right. Also where does that spacer go in the last pic?? How do I figure out the right belt size and install it on the tensioner. Thanks
Last edited by wicked_95z; May 17, 2006 at 08:57 PM.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo that looks right. your bracket is different than mine though so i cannot say for sure. not sure about the belt issue either. i was able to use my same belt when the bracket came back.
Thread Starter
11 Second Club
iTrader: (8)
Joined: Oct 2004
Posts: 430
Likes: 0
From: Jacksonville, NC
Originally Posted by 99.9percenter
Bringing this back from the dead But I have had my SDCE setup for a week or so now and I plan to go ahead and bolt the D1SC to it and connect it to the shortblock.
Z28&WS6 can you seen me some pointers or directions so I can put mine on.
BTW I am located in northeast Arkansas, about and 1.5 hours away from Memphis.
Z28&WS6 can you seen me some pointers or directions so I can put mine on.
BTW I am located in northeast Arkansas, about and 1.5 hours away from Memphis.
