Who's running meth
Thread Starter
7 Second Club
iTrader: (11)
Joined: Jul 2002
Posts: 8,758
Likes: 9
From: Port Tobacco, MD
Who's running meth Looking for some inside info on running meth and the kits available. I'll probably make my own tank just need the pump and other small supporting stuff.
Phil
Phil
I made my own using a ShurFlo pump and some misting nozzles from McMaster Car. I used a Hobbs type switch to fire the pump through a relay. I also used a solenoid inline with the pump for safety. If the pump did not turn off, the solenoid would block the alky flow.
Easy to make, but take a look at Snow Performance's Stage 1 Boost Cooler.
Easy to make, but take a look at Snow Performance's Stage 1 Boost Cooler.
SMC kits are great they have a 2 gallon tank that is super easy to mount and the progressive controller is super easy to calibrate, all you need is 12v poer and a ground the harness comes pre built.
Originally Posted by Phil99vette
My car doesn't have a washer tank.... Plan on making a SS one.
Phil
Phil
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
I use the Coolingmist progressive kit, they have their own 1.5 gallon tank with a low fluid float and sensor. They have an assortment of smaller tanks I just chose this one. Their pump was designed for straight meth, and the kit incorporates a lot of safeguards
With that AFM kit, it says to mount the jet in the intake tube and spray the jet directly at the impeller of the supercharger or turbo. Is that safe? That seems like a bad idea. Why is that location any better than spraying the jet in the cold pipe after the turbo or supercharger? That was on a non-intercooled car. I mounted my jet in the elbow about 8 inches before it enters the TB.
I would shoot it 6 to 8 inches before the tb. In case of condensation fallout. This happens depending on how aggressive you are with it, and how you arrange your jets ECT. I would not want any drops hitting my impeller at speed.
Devilsown makes a good kit. Take a look at there website it should give a decent amount of info you my need. I just have now recently got into alky injection and man it make a big diffrence. Cools the intake charge and allows you to be more aggressive with timing. You will like it I promise.
http://www.alcohol-injection.com/for...lator-351.html
The owner is a really good guy that will go out of his way to help you out.
http://www.alcohol-injection.com/for...lator-351.html
The owner is a really good guy that will go out of his way to help you out.
TECH Apprentice
Joined: Jul 2005
Posts: 381
Likes: 1
From: nashville,tn
I HAVE THE SNOW KIT WORKS GREAT. Kicks in at full throttle, very easy and berry berry nice. Hooks up to windshiled washer tank. And also only use washer fluid that has meth in it and is not I repeat is not deicer.
Originally Posted by SStolen
With that AFM kit, it says to mount the jet in the intake tube and spray the jet directly at the impeller of the supercharger or turbo. Is that safe? That seems like a bad idea. Why is that location any better than spraying the jet in the cold pipe after the turbo or supercharger? That was on a non-intercooled car. I mounted my jet in the elbow about 8 inches before it enters the TB.
I run a dual nozzle alky control kit from Julio installed by OC Corvette. Does it work? Well, the car spins the damn tires all over the place and scares the **** out of me when it does hook, so I guess it does.
