p0200 code help
#1
Staging Lane
Thread Starter
p0200 code help
greetings all,
car seems a little hesitatant/spluttery and jerky especially when moving from 1st to second gear and then car just threw the code p0200, ive searched and realise what the code means.
however where do i even begain to check for problems??
the car is only driven maybe once or twich a month for less than 100 miles,
i first thought it may be bad gas or gas sitting in tank fouling up injectors??? would this cause the code and hesitation??
i also spotted that my pcv valve grommet is split open woild this cause the code, remember reading somewhere about this causing the problem??
any help or imput greatly appreciated
car seems a little hesitatant/spluttery and jerky especially when moving from 1st to second gear and then car just threw the code p0200, ive searched and realise what the code means.
however where do i even begain to check for problems??
the car is only driven maybe once or twich a month for less than 100 miles,
i first thought it may be bad gas or gas sitting in tank fouling up injectors??? would this cause the code and hesitation??
i also spotted that my pcv valve grommet is split open woild this cause the code, remember reading somewhere about this causing the problem??
any help or imput greatly appreciated
#2
Staging Lane
Join Date: May 2010
Location: Harrisburg, PA
Posts: 86
Likes: 0
Received 0 Likes
on
0 Posts
http://www.obd-codes.com/p0200
I'd start here. Some simple voltage checks may get you moving toward a solution.
I'd start here. Some simple voltage checks may get you moving toward a solution.
#3
The only time I've seen P0200 on mine was found to be a bad spark plug wire...the connector had separated from the wire and must have been intermittently losing contact.
The coils and injectors for each bank share a common 12VDC feed, so an electrical problem with the ignition system can apparently show up in the PCM's injector monitoring logic.
I'd start by using a meter to check resistance on each of the 8 injectors, and if none are out of range then I'd pull the spark plug wires and check resistance on each of them. (in my case, removing the wire left the metal clip on the spark plug)
If still no findings, simply apply a dab of dielectric grease to each end of the coil wires and reinstall them...verify a nice clear click when each end seats. My GM wires give 2 clicks on the coil end, and 1 click on the spark plug end.
The coils and injectors for each bank share a common 12VDC feed, so an electrical problem with the ignition system can apparently show up in the PCM's injector monitoring logic.
I'd start by using a meter to check resistance on each of the 8 injectors, and if none are out of range then I'd pull the spark plug wires and check resistance on each of them. (in my case, removing the wire left the metal clip on the spark plug)
If still no findings, simply apply a dab of dielectric grease to each end of the coil wires and reinstall them...verify a nice clear click when each end seats. My GM wires give 2 clicks on the coil end, and 1 click on the spark plug end.
#4
Staging Lane
Thread Starter
Ok im gona go down and take a look today see if anythings loose etc, like i said checked around last nite and did notice the pcv valve/ housing was cracked open
In regards testing where do i evenstart, im good with mechanical issue but stumped with regards electrical. I have a multi meter what setting do i put it on?? Do i prob the injector itself or the harness?? Car on or off?
Car only seems to misbehave when its fully warmed up
In regards testing where do i evenstart, im good with mechanical issue but stumped with regards electrical. I have a multi meter what setting do i put it on?? Do i prob the injector itself or the harness?? Car on or off?
Car only seems to misbehave when its fully warmed up
#5
Staging Lane
Thread Starter
Could bad gas or low gas level cause this??? I let it run extemely low one day and think my prob started after this, also im a demon for leaving it quarter full in garage for weeks, been very hot and humid in nyc as late would moisture have gotten in tank?
#6
Ok im gona go down and take a look today see if anythings loose etc, like i said checked around last nite and did notice the pcv valve/ housing was cracked open
In regards testing where do i evenstart, im good with mechanical issue but stumped with regards electrical. I have a multi meter what setting do i put it on?? Do i prob the injector itself or the harness?? Car on or off?
Car only seems to misbehave when its fully warmed up
In regards testing where do i evenstart, im good with mechanical issue but stumped with regards electrical. I have a multi meter what setting do i put it on?? Do i prob the injector itself or the harness?? Car on or off?
Car only seems to misbehave when its fully warmed up
Set your meter to Ohms. Verify the probes are hooked up to the meter correctly for Ohms, some meters use different plug-in connections but they're usually labeled clearly.
Disconnect each injector, probe across the injector's two pins (orientation doesn't matter) and write down the resistance...should be around 12 Ohms. Post all 8 injector results.
If any of the injectors is significantly different than the rest, stop testing until it's replaced.
If none of the injectors is significantly different, move on to the plug wires. Remove each, probe from end to end ( have to reach up into the plug end to get the metal connector clip) and write down the resistance. Post all 8 plug wire results.
Trending Topics
#10
Staging Lane
Thread Starter
Ok so went down, removed harnesses from injectors, set meter to ohms and to 200k, probed each injector but im getting all kinds of crazy readings, going up and down nothing constant 73.5 .100 etc am im doning some thing wrong. Ignition off key removed, car cold since last nite, not seening any constant reading on any injector.
Please help guys
Many thanks
Please help guys
Many thanks
#14
#18
Staging Lane
Thread Starter
Ok sorry finally got it, checked all from 1-8 and all within 12.1 to 12.5.
Also pulled each harness with engine running and each time once i pilled one the engine ran rougher, couldnt get no7 on quick enough and it threw service engine soon.
Niw i quess i gotta check plug wires, pulled one off and it had spring on end, is this normal, or did i break it? Whats the best way to remove wires, twist yank ????
Also pulled each harness with engine running and each time once i pilled one the engine ran rougher, couldnt get no7 on quick enough and it threw service engine soon.
Niw i quess i gotta check plug wires, pulled one off and it had spring on end, is this normal, or did i break it? Whats the best way to remove wires, twist yank ????
#19
Twist repeatedly to break the seal loose, then pull on the boot (not the wire) while continuing to twist.
I start on the coil end first as they're easier to remove, and when that end is off you can twist the plug end by the boot in a complete circle.
I start on the coil end first as they're easier to remove, and when that end is off you can twist the plug end by the boot in a complete circle.