LS1TECH - Camaro and Firebird Forum Discussion

Gears & Axles Driveshafts | Rearends | Differentials | Gears | 12 Bolt | 9 Inch | Dana

9'' rearend width for stock 4th gen

Thread Tools
 
Search this Thread
 
Old 08-02-2009, 08:39 PM
  #1  
TECH Enthusiast
Thread Starter
iTrader: (-1)
 
lt1badbird's Avatar
 
Join Date: Nov 2008
Posts: 510
Likes: 0
Received 0 Likes on 0 Posts
Default 9'' rearend width for stock 4th gen
hey can anyone please tell me what the width is for a 9" axle in a 4th gen axle flange to axle flange. I have a narrowed 9" in my minitubbed car but im not sure how much it's been narrowed and i'd like to make sure i get the correct backspacing on my drag wheels. Thanks
lt1badbird is offline  
Reply Like
Old 08-02-2009, 08:54 PM
  #2  
11 Second Club
iTrader: (24)
 
Intercooler2's Avatar
 
Join Date: Mar 2008
Location: North East, MD
Posts: 2,554
Likes: 0
Received 2 Likes on 2 Posts
Default
If I recall I think mine was 61"
Intercooler2 is offline  
Reply Like
Old 08-03-2009, 09:36 AM
  #3  
TECH Enthusiast
Thread Starter
iTrader: (-1)
 
lt1badbird's Avatar
 
Join Date: Nov 2008
Posts: 510
Likes: 0
Received 0 Likes on 0 Posts
Default
anyone know for sure?
lt1badbird is offline  
Reply Like
Old 08-03-2009, 10:12 AM
  #4  
TECH Resident
iTrader: (19)
 
demonpixel's Avatar
 
Join Date: Jun 2005
Location: Los Angeles, CA (Burbank)
Posts: 755
Likes: 0
Received 0 Likes on 0 Posts

Default
ask ssvert99, he will know for sure, trust me
demonpixel is offline  
Reply Like
Old 08-03-2009, 10:54 AM
  #5  
TECH Enthusiast
Thread Starter
iTrader: (-1)
 
lt1badbird's Avatar
 
Join Date: Nov 2008
Posts: 510
Likes: 0
Received 0 Likes on 0 Posts
Default
did a little more searching .....4th gens are 64.75" axle flange to flange.
lt1badbird is offline  
Reply Like
Old 08-03-2009, 10:56 AM
  #6  
11 Second Club
iTrader: (24)
 
Intercooler2's Avatar
 
Join Date: Mar 2008
Location: North East, MD
Posts: 2,554
Likes: 0
Received 2 Likes on 2 Posts
Default
Are you talking without backing plates that hold your brake hardware? I am pretty sure where the bare ends are I measured 61"
Intercooler2 is offline  
Reply Like
The following users liked this post:
JsLSk1500 (07-13-2020)
Old 08-03-2009, 11:03 AM
  #7  
11 Second Club
iTrader: (24)
 
Intercooler2's Avatar
 
Join Date: Mar 2008
Location: North East, MD
Posts: 2,554
Likes: 0
Received 2 Likes on 2 Posts
Default
Strange says 29.62" from end to center. X2 = 59.24". With axles 64.72"

http://www.strangeengineering.net/catalog/index.html
Intercooler2 is offline  
Reply Like
The following users liked this post:
Fairbanks346 (10-26-2020)
Tags
Back to Subforum
Gears & Axles
View Next Unread
MWC 9" installed with CM drive shaft; vibrations now in 6th gear




Advanced Search

All times are GMT -5. The time now is 04:31 PM.