QTP headers install ??
QTP headers install ?? I just got my QTP's and am preparing to put them in this weekend. I have read everything I can find on this site but have one question for those who have done it.
The consensus seems to be that the car should be 20" off the ground.
Is the 20" under the wheels or 20" to the bottom of the rocker??
Thanks!!
The consensus seems to be that the car should be 20" off the ground.
Is the 20" under the wheels or 20" to the bottom of the rocker??
Thanks!!
TECH Fanatic
Joined: Nov 2004
Posts: 1,118
Likes: 0
From: TX
The higher you can get it the better. When I did my SLP LT's I used 3-ton stands in the back half way up and had to buy some 6-ton stands for the front and put them about half way up. Jack it up in small increments from side to side, and as always, be careful! I guess to answer your question, get it up about 20 inches to the bottom of the rocker and if they dont go in... raise the car up some more 
Originally Posted by fasteddyss
I just got my QTP's and am preparing to put them in this weekend. I have read everything I can find on this site but have one question for those who have done it.
The consensus seems to be that the car should be 20" off the ground.
Is the 20" under the wheels or 20" to the bottom of the rocker??
Thanks!!
The consensus seems to be that the car should be 20" off the ground.
Is the 20" under the wheels or 20" to the bottom of the rocker??
Thanks!!
Originally Posted by code4
Not sure of the exact height but I had to turn my driver side header straight up for it to go in without having to remove anything. Including the oil filter/plug.
Originally Posted by NviouSS
how much do QTP's weigh compared to other headers?
the boox i get them shipped in said 25#'s thats headers, header gaskets, 02 extensions, and Air Tube gaskets
Y-pipe and Strange 8 Locking header bolts are on there way soon back-order
Trending Topics
Teching In
Joined: Mar 2004
Posts: 36
Likes: 0
I have a question for anyone ,I tried to install a set of hooker headers but the drivers side hits on the floorboard.Is it possible the engine is sitting or leaning to one side,and if so can you adjust on the motor mounts?
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Gifts Neither Your Dad Nor Grad Will Shove Into the 'Trinket Drawer'
Brett Foote
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Originally Posted by BlackVader
I have a question for anyone ,I tried to install a set of hooker headers but the drivers side hits on the floorboard.Is it possible the engine is sitting or leaning to one side,and if so can you adjust on the motor mounts?
I also need to know how high to get the car, 20" to the k-member doesnt seem like enough. Depending on how high I have to get the car, I may make 2 stands out of 6x6's.
Originally Posted by NviouSS
how much do QTP's weigh compared to other headers?
11 Second Club
Joined: Oct 2002
Posts: 1,400
Likes: 0
From: NY,CT & MA
nice choice.. i got the QTPs also...
I used a lift to get mine in ... i am a tall guy.. 6'4'' and i need the car to be very high off the ground for me to work under it..lol.... but they went right in without any problems..
good luck with the install
i got the QTPs also...I used a lift to get mine in ... i am a tall guy.. 6'4'' and i need the car to be very high off the ground for me to work under it..lol.... but they went right in without any problems..
good luck with the install
!LS1 11 Second Club
Joined: Apr 2003
Posts: 7,133
Likes: 2
From: Miami
I jacked the car up as high as my largest rolling jack would go (it's a 21" jack) + a piece of 4"x4" blocking was used between the jack and the K-member lift point. I had the rear tires up on Rhino ramps. So figure at least 2' clear from floor to bottom of K-Member.
QTP's slid right in. Slide them in with the collector aiming down.
QTP's slid right in. Slide them in with the collector aiming down.
Thanks for the input guys!!
I have the car up about 20" now as I was rebuilding the tranny. I was going to put it on the suspension to install my new SFC's. I will see how high I can get it safely.
I have 2 huge jack stands I can use on the rear axle. I am making blocks out of wood to go under the front tires. I should be able to get over 2'
I have the car up about 20" now as I was rebuilding the tranny. I was going to put it on the suspension to install my new SFC's. I will see how high I can get it safely.
I have 2 huge jack stands I can use on the rear axle. I am making blocks out of wood to go under the front tires. I should be able to get over 2'
