Need Bellows without MAF??

Reply Subscribe

Thread Tools

Search this Thread

Jul 27, 2005 | 02:43 PM

Bill Bowling

Thread Starter

TECH Addict

iTrader: (6)

Joined: Apr 2003

Posts: 2,597

Likes: 4

From: Lawrenceville, GA

Need Bellows without MAF??

I am planing on removing my MAF and wanted to know what everyone is using as a bellow between the TB and Lid.
I guess I could go to HomeDepot but would like to have something that looks good.
Bill

Jul 27, 2005 | 11:23 PM

slowpoke96z28

TECH Addict

iTrader: (2)

Joined: May 2005

Posts: 2,099

Likes: 9

From: cedar hill, tx

try a short piece of 3 inch exhaust pipe in th section where th MAF was. what engine management system are you going with? Speed density? Alpha-N? or something else?

Jul 28, 2005 | 03:23 PM

Bill Bowling

Thread Starter

TECH Addict

iTrader: (6)

Joined: Apr 2003

Posts: 2,597

Likes: 4

From: Lawrenceville, GA

Quote:

Originally Posted by slowpoke96z28

try a short piece of 3 inch exhaust pipe in th section where th MAF was. what engine management system are you going with? Speed density? Alpha-N? or something else?

SD.

Bill

Jul 30, 2005 | 06:56 PM

Bill Bowling

Thread Starter

TECH Addict

iTrader: (6)

Joined: Apr 2003

Posts: 2,597

Likes: 4

From: Lawrenceville, GA

So no one makes something to go beteen TB and aftermarket air lid??

Bill

Jul 30, 2005 | 07:33 PM

TAQuickness

TECH Junkie

iTrader: (28)

Joined: Jan 2004

Posts: 3,250

Likes: 1

From: Houston

Hey Bill - I'm in the same boat. I just got done with the micrometer on my 85mm MAF. As it turns out, I have one SLP slashed exhaust tip in my parts bin, which ironically has a near identicle ID as the 85mm MAF. I was planning to cut it down and use it inplace of the MAF.

I think I have enough material to fab 2 of these. If this works out ok, and you don't mind splitting the cost of the tip with me, I can send you the other one.

If it doesn't work, I was planning on browsing the plumbing section @ Home Depot.

Jul 31, 2005 | 03:09 PM

Bill Bowling

Thread Starter

TECH Addict

iTrader: (6)

Joined: Apr 2003

Posts: 2,597

Likes: 4

From: Lawrenceville, GA

Quote:

Originally Posted by TAQuickness

Hey Bill - I'm in the same boat. I just got done with the micrometer on my 85mm MAF. As it turns out, I have one SLP slashed exhaust tip in my parts bin, which ironically has a near identicle ID as the 85mm MAF. I was planning to cut it down and use it inplace of the MAF.

I think I have enough material to fab 2 of these. If this works out ok, and you don't mind splitting the cost of the tip with me, I can send you the other one.
If it doesn't work, I was planning on browsing the plumbing section @ Home Depot.

I already made an insert for mine last night. I used a 3" S&D Coupling PVC part#22733 from Lowe's. It cost $1.08.... I put the SS on it. I had one left over from my calipters. I had to cut the ridge out of the middle and I also painted the outside black. It does not look to bad. See picture. I would still like to have a bellow that went from the lid to the TB. If you find someone that has one please let me know.

Bill

Attached Thumbnails

Reply Subscribe

Reply Share

First
Prev
1 / 1
Next
Last