Lanes true duals?
Thread Starter
10 Second Club
Joined: Mar 2005
Posts: 142
Likes: 0
From: Jones, OK
Lanes true duals? I was told that he is the man i need to talk to to get them ran out the ***. Does anyone no how i can get ahold of him? i have big tubes kooks and wanna run mandrelly bent X Pipe with mufflers then run it out the back. But my big deal is trying to get ground clearance. car is not lowered but will b seeing the sky shortly. 
so can anyone help me please. name or Sn where i can get ahold of him. thanks in advance.
Joe
so can anyone help me please. name or Sn where i can get ahold of him. thanks in advance.Joe
TECH Senior Member
iTrader: (10)
Joined: Nov 2001
Posts: 8,766
Likes: 0
From: Gainesville, Denton TX
Very nice work, going over the axle will be very nice, I'd still like to have him finish mine up over the axle, but time and money keep me from it.
My dumped setup tucks up nicer than most Y-Catback setups that I've seen or been around, very very nice clearance.
My dumped setup tucks up nicer than most Y-Catback setups that I've seen or been around, very very nice clearance.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo Thread Starter
10 Second Club
Joined: Mar 2005
Posts: 142
Likes: 0
From: Jones, OK
Thanks for all the info everyone has given me. Also did u guys have to take your car to him or does he just bend it then send it to you? If i have to take my car to him i will if its somewhere close. but would much prefer a pre bent setup that all i have to do is have it welded on. Once again guys thanks for all the info. and if anyone can help me find out about if i have to take my car to him id greatly appreciate it.
Thanks,
Joe
Thanks,
Joe
He shipped mine to me fully welded ready to clamp onto the headers. The system tucked up very nice and is easy as hell to install. If you want it run out the back you're going to have to go see him. I believe he's down in North Richland Hills or somewhere around there so its not too far of a drive. Definitely worth it IMO. Good luck.
Originally Posted by Brandon
Very nice work, going over the axle will be very nice, I'd still like to have him finish mine up over the axle, but time and money keep me from it.
My dumped setup tucks up nicer than most Y-Catback setups that I've seen or been around, very very nice clearance.
My dumped setup tucks up nicer than most Y-Catback setups that I've seen or been around, very very nice clearance.
My buddy's T/D set up from Lane's is tucked up way better than my ORYP from TSP. I'd hate to be lowered with my current setup!
PM sent to keep the paying sponsors happy. Lane, why don't you sponsor this board so we don't have to sneak behind the admins backs giving out your info? 
Originally Posted by 10secopcar
so does anyone actually no what city and state he is in?