Headers 4 lowered car.

Reply Subscribe

Thread Tools

Search this Thread

May 28, 2006 | 11:05 PM

BlueSS346

Thread Starter

Staging Lane

Joined: Nov 2005

Posts: 65

Likes: 0

From: Montgomery County Pa

Headers 4 lowered car.

I'm tossing around the idea of getting headers for my car. I was looking at the Pacesetters and catted y pipe. My car is lowered an inch with Hotchkis springs and was wondering what headers won't give me major clearence problems. Also, what does an instal usually run price wise?

Last edited by BlueSS346; May 28, 2006 at 11:11 PM.

May 28, 2006 | 11:19 PM

RrCoX22

TECH Addict

iTrader: (6)

Joined: Jun 2005

Posts: 2,210

Likes: 0

From: Ft. Bragg, NC

anything will do fine except for SLP's, they hang the lowest.... and do it yourself

May 28, 2006 | 11:20 PM

gus99ssm6

On The Tree

Joined: Aug 2003

Posts: 102

Likes: 0

From: Las Vegas

I have Jet-Hots and Hotchkis springs with true duals, Daily driver. It only scrapes on really big speed bumps. I dont think its a problem.

May 28, 2006 | 11:39 PM

orangeapeel

ЯєŧąяĐ Єl¡m¡иąŧøя ™

iTrader: (18)

Joined: Nov 2004

Posts: 16,083

Likes: 4

From: Justin, TX

FLP's tuck nicely. Also depends on how much drop you are looking at going with.

May 29, 2006 | 08:15 AM

davered00ss

Moderator

iTrader: (4)

Joined: Nov 2003

Posts: 10,520

Likes: 0

From: Plainfield, CT

Kooks work great for a lowered car.

May 29, 2006 | 08:17 AM

davered00ss

Moderator

iTrader: (4)

Joined: Nov 2003

Posts: 10,520

Likes: 0

From: Plainfield, CT

Kooks on my SS.

DS loop. Hangs lower than the headers.

May 29, 2006 | 01:34 PM

stevensLS1

TECH Addict

iTrader: (2)

Joined: Jun 2004

Posts: 2,303

Likes: 0

From: houston tx

damn those kooks tuck up damn nice! ive got sportlines on my car so those will be next! thanks for the pic.

also i agree with what was said above. just depends on how much you wanna spend.

Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?

Pouria Savadkouei

Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine

Verdad Gallardo

7 Most Reliable High-Performance Engines GM Has Ever Built

Verdad Gallardo

Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin

Verdad Gallardo

6 Common C5 Corvette Failures and What's Involved In Repairing Them

Pouria Savadkouei

Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph

Verdad Gallardo

Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked

Pouria Savadkouei

Top 10 Most Powerful Chevy Trucks Ever Made!

Hennessey's New Supercharged Silverado ZR2 Has 700 HP

Verdad Gallardo

Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes

Verdad Gallardo

May 29, 2006 | 02:12 PM

TheBlurLS1

That's what she said...

iTrader: (8)

Joined: Mar 2004

Posts: 7,954

Likes: 2

From: Nederland Texas

Kooks headers and y-pipe have tucked in nicer than anything I've seen, this was even a catted-y setup. They are clearanced to fit under the chassis brace under the driverside floor board. This is the point where all clearance goes to ****.

May 29, 2006 | 02:15 PM

#10

Beasst8

TECH Fanatic

iTrader: (1)

Joined: Nov 2005

Posts: 1,142

Likes: 0

From: Goldsboro, NC

I love these posts. I have the Pacestters LT's with ORY. I GAINED 3/4 in ground clearence under the driver seat with the install. The price can go from 350 up to as high as 600 (thats crazy high). I am in the Carolinas, they wanted 400-450 down here. Was a little worried going in, but looking back, I'd do it all over again. My wife and I did it in 9 hours first time. Good luck

Last edited by Beasst8; May 29, 2006 at 02:24 PM.