slt200mph

iTrader: (42)

Looks like a high quality Y pipe the merge is very good fabrication and should flow very well... is the pipe completely round or is it flat on the drivers side for clearance??

LS1 Freak

iTrader: (7)

Its a little flat, not really noticable, definatly not like the stock Y. I doubt I will have any clearance issues, I'll post pics when everything is installed and of course the dyno results

_JB_

iTrader: (33)

Awesome headers! I want a set so bad. Too bad I lost my job

GG01SS

iTrader: (1)

Nice headers, when I'm ready for a cam I will be installing a set of these. With good tires you should be in the 12's. Get a stall next for mid to low 12's.

LS1 Freak

iTrader: (7)

I was thinking about it but I'm afraid I'll snap the rear or brake the tranny, I dont know.My car has only 24K miles on it and I kinda dont want to turn it into a race car, but I still might do a stall

NHRAMAN

iTrader: (1)

cool..go make some noise........

LS1 Freak

iTrader: (7)

The cops in Orlando are gonna love me, I dont really care though, I want it loud that way when I have someone next to me banging his 2 subwoofers, I can rev up that 350 and scare the leaving **** out of them, especially down here,its crazy

The Alchemist

iTrader: (19)

That is arguably the nicest ypipe out there.

Rob98LS1

iTrader: (5)

The Y-merge beats the hell out of my Edelbrocks, I should of went with ARH.

Nice headers!!

bmax

iTrader: (1)

Good choice.
They install easy, fit nice.

ssgunny

iTrader: (6)

Nice pieces and are the one's I planned to go with although I would prefer the catted version.

I guess the majority of aftermarket Y's neck down to 2 3/4" as this one appears to do also. It just seems crazy that you have headers with collector sizes of 3" each and then that flow has to get shoved in to ONE hole less than half of that size.

LS1 Freak

iTrader: (7)

The Y neck might be 2 3/4 but it hooks up to my SLP CME which is 3''. I wish I could afford true duals, oh well, now the only thing I'm worry about is the rasp! If it sound raspy, I guess bullets would be my next purchase,I'll know possibly this week or Monday!
Happy Thanksgiving to all!!!

hammerhead

iTrader: (1)

Good choice! I didn't see anywhere if you've got cats or not, but regardless it's going to be loud as hell with the LM. I've got a GMMG and I ended up putting a Magnaflow bullet in the I and I like it. Happy turkey day.

LS1 Freak

iTrader: (7)

The car will probably be done tomorrow and I'll see if its gonna sound raspy, I gidnt get the catted Y but I might get couple of bullets if its too loud and raspy, I'll post new pics and dyno results, hopefully good #'s

ls2 bait

iTrader: (11)

congrats man. if they were polished i would have went with them over my qtp's. im sure clearance is worlds better.

LS1 Freak

iTrader: (7)

I will see tomorrow(maybe) As far as I have seen those headers on other cars, there isnt any clearance issues,even with lowered cars, I cant wait

ssgunny

iTrader: (6)

I believe you and (I think) all of the OEM stuff did that so the aftermarket followed suit. I think that when I get my system I will cut off the part of te Ypipe that reduces to 2 3/4". Then have a pipe fabricated to keep it as close to 3" as possible.

Ditto on the turkey day.

hammerhead

iTrader: (1)

My AR Y is 3" straight back. I had the GMMG I bumped out to fit over it.

LS1 Freak

iTrader: (7)

Mine Y is also from front to back 3''

BriancWS6

iTrader: (18)

Very nice!