02 WS6 Knocking Please Help !!!!!

Reply Subscribe

Thread Tools

Search this Thread

Nov 3, 2009 | 06:59 PM

#21

twadd

Thread Starter

Teching In

iTrader: (1)

Joined: Jun 2008

Posts: 20

Likes: 0

From: Gadsden,AL

Quote:

Originally Posted by capt.ld

dam i better check mine like that couse i have a funny sound at 2500 rpm and im thinking a rod also.but mine at cold nocks and warm it does it at 25 and up but not louder just stays the same and dont go away.

LS1 noise sux !!

Nov 3, 2009 | 07:09 PM

#22

capt.ld

On The Tree

iTrader: (7)

Joined: Dec 2008

Posts: 107

Likes: 0

From: elizabethtown.ky

yea it does i just wounder if i can change the rod barrings in the car from the bottom.ill half to drop the oil pan and check them all.god thats going to suck bad.couse im not sure what it is.

Nov 3, 2009 | 07:17 PM

#23

twadd

Thread Starter

Teching In

iTrader: (1)

Joined: Jun 2008

Posts: 20

Likes: 0

From: Gadsden,AL

Quote:

Originally Posted by capt.ld

yea it does i just wounder if i can change the rod barrings in the car from the bottom.ill half to drop the oil pan and check them all.god thats going to suck bad.couse im not sure what it is.

Just a guessing game huh? You gonna tackle that soon ?

Nov 3, 2009 | 07:18 PM

#24

rdd014camaro

On The Tree

iTrader: (8)

Joined: Jun 2009

Posts: 106

Likes: 1

From: Fort Worth, TX

That does kinda sound like a spun bearing. with only 25k on the car. that sucks dude. just replaced my engine due to a bad rod bearing.

Nov 3, 2009 | 07:21 PM

#25

twadd

Thread Starter

Teching In

iTrader: (1)

Joined: Jun 2008

Posts: 20

Likes: 0

From: Gadsden,AL

Quote:

Originally Posted by rdd014camaro

That does kinda sound like a spun bearing. with only 25k on the car. that sucks dude. just replaced my engine due to a bad rod bearing.

You just replaced the whole engine ? That cost a pretty penny !

Nov 3, 2009 | 07:22 PM

#26

rdd014camaro

On The Tree

iTrader: (8)

Joined: Jun 2009

Posts: 106

Likes: 1

From: Fort Worth, TX

You can buy an in car engine bracket from harbor freight. Basically it grabs the engine and mounts to the shock mounts. Then you can drop the subfram and have everything right there. Getting a crank turned is about 90 bucks. Or you can just buy the crank kit which comes with crank and appropriate main and rod bearings for about 250bucks. just make sure your rod diamater hasnt gotten beat out of roundness

Nov 3, 2009 | 07:24 PM

#27

rdd014camaro

On The Tree

iTrader: (8)

Joined: Jun 2009

Posts: 106

Likes: 1

From: Fort Worth, TX

well i found a short block with about 35k on it for cheap. didnt feel like tearing into the engine. even though its not to bad. I just wanted to pull one out and put the other right back in

Nov 3, 2009 | 07:27 PM

#28

twadd

Thread Starter

Teching In

iTrader: (1)

Joined: Jun 2008

Posts: 20

Likes: 0

From: Gadsden,AL

Quote:

Originally Posted by rdd014camaro

well i found a short block with about 35k on it for cheap. didnt feel like tearing into the engine. even though its not to bad. I just wanted to pull one out and put the other right back in

I dont blame you.