It's Alive!!!!
Thread Starter
TECH Fanatic
iTrader: (2)
Joined: Dec 2002
Posts: 1,107
Likes: 0
From: Orange county n.y.
It's Alive!!!! Well i finally finished installing my new LME 408 and it sounds awesome 
Here is my list. Any HP guess's and opions welcome.
LME 408
AFR225's 69cc's w/ manley nextek double springs
Cam Motion 253/257 643 646 112lsa
Custom Wiseco pistons W 2.5cc valve reliefs and lateral gas ports
NPR stainless rings
eagle crank
callies rods
crane lifters
felpro .041 head gaskets
Jessel ss rockers
comp high tek push rods
Roll master double chain
ls6 ported pump
kook's stepped 1 3/4- 1 7/8 headers
Ported LSX 90mm w/ NW 90mm TB
85 mm MAF & TSP 85mm lid
TSP X pipe exhaust.
Also all ARP and all good stuff inside
Thanks to Bryan @ LME and alot of thanks to my friend
LT1PWR {James} for all of his install help
Time for a SIG change
Here is my list. Any HP guess's and opions welcome.LME 408
AFR225's 69cc's w/ manley nextek double springs
Cam Motion 253/257 643 646 112lsa
Custom Wiseco pistons W 2.5cc valve reliefs and lateral gas ports
NPR stainless rings
eagle crank
callies rods
crane lifters
felpro .041 head gaskets
Jessel ss rockers
comp high tek push rods
Roll master double chain
ls6 ported pump
kook's stepped 1 3/4- 1 7/8 headers
Ported LSX 90mm w/ NW 90mm TB
85 mm MAF & TSP 85mm lid
TSP X pipe exhaust.
Also all ARP and all good stuff inside
Thanks to Bryan @ LME and alot of thanks to my friend
LT1PWR {James} for all of his install help
Time for a SIG change
Trending Topics
Thread Starter
TECH Fanatic
iTrader: (2)
Joined: Dec 2002
Posts: 1,107
Likes: 0
From: Orange county n.y.
Last night was the start up ran it for 25 minutes between 1500-2000rpm. Now i need a tune then we will have some #'s and track times 
As far as a video goes i'll take some but i'll need help with setting it up on the site. I will try to get video of it idleing on monday or tuesday. I can't wait to drive it and feel the POWER BTW even with my old tune this cam idles at about 1050-1100 rpm and it sounds nice, Can't wait for a full tune 
As far as a video goes i'll take some but i'll need help with setting it up on the site. I will try to get video of it idleing on monday or tuesday. I can't wait to drive it and feel the POWER BTW even with my old tune this cam idles at about 1050-1100 rpm and it sounds nice, Can't wait for a full tune LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
Five Reasons the Camaro Was the Most Pivotal Player in the Pony Car Wars 2.0
Brett Foote
10 Reasons the LS7 Is GM's Most Extreme Naturally Aspirated V8 Engine Ever
Verdad Gallardo
Thread Starter
TECH Fanatic
iTrader: (2)
Joined: Dec 2002
Posts: 1,107
Likes: 0
From: Orange county n.y.
as far as breaking it in i was told to run it for 20-25 min between 1500-2000 rpm and then i could have it dyno tuned. What i would like to do is to be able to drive to eastside for the tune which is a hundred something miles away then have it tuned. Kinda in a rough situation with it needing a tune i do not want to drive it to much but i would like to get some miles on it as well 
Z'mnypit, congrats on your motor
Z'mnypit, congrats on your motor
