Tips on cutting SS hose

Reply Subscribe

Thread Tools

Search this Thread

Oct 29, 2005 | 08:04 AM

Phil99vette

Thread Starter

7 Second Club

iTrader: (11)

Joined: Jul 2002

Posts: 8,758

Likes: 9

From: Port Tobacco, MD

Tips on cutting SS hose

Does anyone have any tips on how to cut SS hose to keep the SS braided cover cut clean.
Phil

Oct 29, 2005 | 08:13 AM

stevemilz

TECH Enthusiast

iTrader: (3)

Joined: Sep 2004

Posts: 672

Likes: 0

From: Michigan

I wrap it with electrical tape and use a cut off wheel (dremel works good also).

Oct 29, 2005 | 08:14 AM

TN_TRITON

Staging Lane

iTrader: (16)

Joined: Sep 2005

Posts: 53

Likes: 0

From: Soddy Daisy, Tennessee

Wrap the hose in masking tape where you are cutting. Then cut through the tape and it will help the braid to cut cleaner without fraying.

Oct 29, 2005 | 08:36 AM

Phil99vette

Thread Starter

7 Second Club

iTrader: (11)

Joined: Jul 2002

Posts: 8,758

Likes: 9

From: Port Tobacco, MD

I tried using a chop saw and it seemed to fray it pretty good on the bottom side. I guess I will try a grinder with a thin cutoff wheel.
Phil

Oct 29, 2005 | 08:41 AM

Jake the SSnake

TECH Enthusiast

iTrader: (11)

Joined: Dec 2002

Posts: 529

Likes: 1

From: Iowa

Quote:

Originally Posted by stevemilz

I wrap it with electrical tape and use a cut off wheel (dremel works good also).

This is what I do(dremel). I think I read in one of my car mags to take a sharp chisel and give it a whack with a hammer haven't tried it yet though.

Oct 29, 2005 | 10:24 AM

BAKED

9 Second Club

iTrader: (14)

Joined: Oct 2004

Posts: 1,601

Likes: 2

From: kentucky

I've heard of that too.

Oct 29, 2005 | 11:29 AM

hotrodrx7

On The Tree

iTrader: (13)

Joined: Sep 2005

Posts: 111

Likes: 0

The shop where I get my braided hose wraps it with reinforced tape then cuts it with bolt cutters.

6 Gifts Neither Your Dad Nor Grad Will Shove Into the 'Trinket Drawer'

Brett Foote

Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?

Pouria Savadkouei

Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine

Verdad Gallardo

7 Most Reliable High-Performance Engines GM Has Ever Built

Verdad Gallardo

Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin

Verdad Gallardo

6 Common C5 Corvette Failures and What's Involved In Repairing Them

Pouria Savadkouei

Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph

Verdad Gallardo

Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked

Pouria Savadkouei

Top 10 Most Powerful Chevy Trucks Ever Made!

Hennessey's New Supercharged Silverado ZR2 Has 700 HP

Verdad Gallardo

Oct 29, 2005 | 08:33 PM

mattr228

Launching!

iTrader: (10)

Joined: Dec 2004

Posts: 287

Likes: 0

From: GI, NE

you should use a 32 teeth/ inch hacksaw blade when cutting it .. wrap it in masking tape and cut it in the middle of the tape

Oct 29, 2005 | 10:59 PM

#10

Richiec77

TECH Fanatic

iTrader: (3)

Joined: Dec 2003

Posts: 1,799

Likes: 1

From: I play with Sand!!

DO the cold chisle and it'll work Great. You'll want to grind roughly a 45 deg bevel on the chisel. You'll also need some Aluminum to do it too. I saw that in a Mag and gave it a shot. Works great.

Oct 30, 2005 | 01:24 AM

#11

racecar

TECH Resident

Joined: Aug 2004

Posts: 875

Likes: 2

From: Portland Oregon

Wrap tight with silver duct tape and use an air powered thin cut off wheel. You can cut without one frayed wire.

Oct 30, 2005 | 03:34 AM

#12

tbojbob

Launching!

Joined: Mar 2002

Posts: 202

Likes: 0

From: nowhere in particular

Whack it w/a cold chisel on a piece of 1/4" (minimum) thick aluminum (6" x 6" will do). Make sure the chisel has a good edge on it.

Oct 30, 2005 | 06:15 AM

#13

baldurann

12 Second Club

iTrader: (15)

Joined: Sep 2004

Posts: 576

Likes: 0

From: Kingwood, TX

I'd say use a cutoff wheel on a dremel, or something to that effect.

Oct 30, 2005 | 09:08 AM

#14

Phil99vette

Thread Starter

7 Second Club

iTrader: (11)

Joined: Jul 2002

Posts: 8,758

Likes: 9

From: Port Tobacco, MD

I used a cutoff wheel in a grinder, 3m masking take and worked awesome. Some grease ont he fittings and they slid right togther. I was really amazed at how easy they went together.
Phil

Oct 30, 2005 | 10:21 AM

#15

Moparnos (The SLP Guy)

Flossin' twin turbos

iTrader: (55)

Joined: Jun 2004

Posts: 3,148

Likes: 0

From: Chicago

Quote:

Originally Posted by hotrodrx7

The shop where I get my braided hose wraps it with reinforced tape then cuts it with bolt cutters.

from my experience this seems to leave the cleanest cut

Oct 30, 2005 | 12:46 PM

#16

hondo

TECH Resident

iTrader: (2)

Joined: Apr 2004

Posts: 833

Likes: 0

From: in the Trans Am

Quote:

Originally Posted by mattr228

you should use a 32 teeth/ inch hacksaw blade when cutting it .. wrap it in masking tape and cut it in the middle of the tape

i wrap it tightly in that strapping tape, i also put TWO 32 tpi blades in my hacksaw going in opposite directions. i havent tried the chisel method but i'll have to test it