what else do i need
what else do i need i have a the cam in my sig.... what else do i need to intall it... i have rods and the 98-02 LS1 Patriot "Gold" Dual Valve Spring Kit... is there any thing elst that i have to have to put this cam in... thanks...
neither, timing chain cover gasket, new crank pulley bolt, etc, etc
go to SDPC2000.com they are a sponsor here, if you look around in the LS section you can find a gasket kit for cam swaps
Good luck
AJ
go to SDPC2000.com they are a sponsor here, if you look around in the LS section you can find a gasket kit for cam swaps
Good luck
AJ
here are some suggestions - some are required, some are optional...I'm doing mine this weekend and will be using every part listed below...do it once, do all the right parts, and be confident you did everything you needed to 
Good luck!
optional = *
2 pen magnets
Antifreeze (1 jug) Dexcool
Distilled Water (2 jugs)
Syn Oil (7 qrts)
Conv Oil (7 qrts)
Oil Filter (2)
*5/16" or 1/4" Wooden Dowels (Lifter Holder)
Timing Chain (LS2)
*Oil Pump (LS6)
Bolt and Gasket Kit
*Water Pump (OEM) - depending on miles
Valve Spring Compressor
Locktite (Red - Medium)
Pulley Puller (RENTAL)
High Temp RTV Sealant
Anti-seize
*Retainer Locks (10 Extra)
*Oil Pump O-Ring (2)
Pulley Install Tool
Good luck!optional = *
2 pen magnets
Antifreeze (1 jug) Dexcool
Distilled Water (2 jugs)
Syn Oil (7 qrts)
Conv Oil (7 qrts)
Oil Filter (2)
*5/16" or 1/4" Wooden Dowels (Lifter Holder)
Timing Chain (LS2)
*Oil Pump (LS6)
Bolt and Gasket Kit
*Water Pump (OEM) - depending on miles
Valve Spring Compressor
Locktite (Red - Medium)
Pulley Puller (RENTAL)
High Temp RTV Sealant
Anti-seize
*Retainer Locks (10 Extra)
*Oil Pump O-Ring (2)
Pulley Install Tool
geese...dual valve springs for that little of a cam.
but the list above looks pretty good. a few things ill add to it are:
By saying "rod" i guessing you mean pushrod??, if not you will need those
New retainers
Pick up some extra locks(keepers), you will loose some. trust me. they are only like $1 a piece anyway.
but the list above looks pretty good. a few things ill add to it are:
By saying "rod" i guessing you mean pushrod??, if not you will need those
New retainers
Pick up some extra locks(keepers), you will loose some. trust me. they are only like $1 a piece anyway.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo This kit includes Patriot "Gold" Dual Springs, Titanium Retainers, Machined bases (seats), Super 7 Locks, & Viton Rubber Seals. plus Trick Flow Chromemoly Pushrods and cam.... this is all that i have right now... and thanks for the help
Originally Posted by mark.deady
This kit includes Patriot "Gold" Dual Springs, Titanium Retainers, Machined bases (seats), Super 7 Locks, & Viton Rubber Seals. plus Trick Flow Chromemoly Pushrods and cam.... this is all that i have right now... and thanks for the help