GRP Rods ?????
GRP Rods ????? Well I didnt do much research buying these and wondering if I shoulda waited for a set of "steel" rods. They were exactly the size I needed and couldnt beat the price. They are the 2200 series and were just redone. I would be useing them in a LS2 with 4.005 wiesco blower/N20 pistons that weigh 467grams and stock crank with 24x. The rods weigh 503 grams. Supposilly you should run a lighter than piston than rod with the alluminum rods? I got that covered i believe. So what about street use?? The car is in sig and is my weekend ride with occasional track use. Are these rods no good for the street or stick with them?? I have done a search but no luck. thanks
Billet aluminum rods don't tend to last on the street, the heat cycles is what hurts them, and they need about .020" additional clearance over a steel rod.
If your piston is normally .008" out of the hole, with a GRP rod your pistons would need to be .012" in the hole.
The Bill Miller forged rods tend to last a lot better on the street, rather then cut from a billet blank, they're forged to shape, so the grain structure goes around the small end and big end of the rod, rather than the small end and big end of the rod cutting through the straight grain structure of the billet rods.
There is no way I would run those on a street car for more than one season.
Read more here.
http://www.bmeltd.com/rods.htm
If your piston is normally .008" out of the hole, with a GRP rod your pistons would need to be .012" in the hole.
The Bill Miller forged rods tend to last a lot better on the street, rather then cut from a billet blank, they're forged to shape, so the grain structure goes around the small end and big end of the rod, rather than the small end and big end of the rod cutting through the straight grain structure of the billet rods.
There is no way I would run those on a street car for more than one season.
Read more here.
http://www.bmeltd.com/rods.htm
Launching!
Joined: Sep 2009
Posts: 260
Likes: 0
From: greensboro, nc
I hope that by stating the rods have ben redone you didn't buy a used set of aluminum rods. The life span of an aluminum rod is very short and built for race apps only not intended for street use.
If they are new alum rods they can be run on the street but there just alot more things you need to worry about and do to make them live longer.
If there used it taking a huge shot in the dark to use them. so polish them up and use them to make a glass coffee table
Another issue that arises from buying rods unseen, not all shelf pistons will fit an aluminum rod, aluminum rods are typically twice as thick over the pin, vs. steel.
Wiseco, their dish pistons specially, need to keep over the pin thickness to around .250", by default small end width will be 1.040", too wide for alot of shelf pistons, both dimensions are specified when initial ordering.
Aluminum rods breaking, happens lot less nowadays, when an aluminum rod breaks, minimal collateral damage. Steel rod breaks it gets nasty, doesn't want to let go.
Wiseco, their dish pistons specially, need to keep over the pin thickness to around .250", by default small end width will be 1.040", too wide for alot of shelf pistons, both dimensions are specified when initial ordering.
Aluminum rods breaking, happens lot less nowadays, when an aluminum rod breaks, minimal collateral damage. Steel rod breaks it gets nasty, doesn't want to let go.
Last edited by AES Racing; Nov 21, 2010 at 10:09 PM.
Trending Topics
Another issue that arises from buying rods unseen, not all shelf pistons will fit an aluminum rod, aluminum rods are typically twice as thick over the pin, vs. steel.
Wiseco, their dish pistons specially, need to keep over the pin thickness to around .250", by default small end width will be 1.040", too wide for alot of shelf pistons, both dimensions are specified when initial ordering.
Aluminum rods breaking, happens lot less nowadays, when an aluminum rod breaks, minimal collateral damage. Steel rod breaks it gets nasty, doesn't want to let go.
Wiseco, their dish pistons specially, need to keep over the pin thickness to around .250", by default small end width will be 1.040", too wide for alot of shelf pistons, both dimensions are specified when initial ordering.
Aluminum rods breaking, happens lot less nowadays, when an aluminum rod breaks, minimal collateral damage. Steel rod breaks it gets nasty, doesn't want to let go.
. Thanks for the advise guys.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
Five Reasons the Camaro Was the Most Pivotal Player in the Pony Car Wars 2.0
Brett Foote
