Gauging interest: LS2 402/4L80e, 98 Camaro
#1
COMPLETE Z28 part out, 402, 4L80e, ebony interior, EVERYTHING
My car has had a misfortunate run-in with a tree. The car needs a new rear bumper, hatch, berger panel, spoiler and paintwork. I do not have the time to deal with it so I am parting it out
The car is a 1998 Z28 and is Sebring Silver in color. The interior is ebony. I am located in Owasso, Oklahoma. Verified Paypal with plenty of history/feedback on this site. The motor, transmission, and rear end are fully documented. They were assembled and installed by professionals and are in absolutely perfect condition.
If you feel inclined to repair the rear end on this car and have an outstanding vehicle you can purchase it from me for $12,000 OBO. I am also open to trades/partial trades on a sportbike 600cc and up, decent daily driver or 4 wheel drive vehicle.
Pictures will be up ASAP.
SDPC built LS2 based 402 stroker with less than 7500 miles since install
Parts list:
-GM LS2 aluminum block
-GM bell housing dowels,
-GM head dowels,
-GM main bolts,
-Durabond cam bearings,
-GM drain plug, dumbell plug and drain plugs,
-Clevite main bearings,
-Eagle crankshat,
-Skat connecting rods,
-Clevite rod bearings,
-Manley pistons (-12cc),
-Total Seal Piston rings,
-SDPC Timing Set,
-Katech Sensor Harness,
-Manley pushrods,
-LS7 oil pump and LS7 lifters,
-.040 Cometic head gasket set,
-ARP head bolts
-GM Valley cover
$7000+ new from SDPC with receipts, asking $5000 buyer pays shipping and paypal fees
*I can supply all parts numbers of parts used from SDPC receipts as well as full SDPC and professional installation*
Full Assembled L92 heads
-milled to 62cc chamber from the factory 70cc for a bump in compression. I believe they can be milled down to 59cc if desired but I am not certain. They have the GM 2.16/1.59 intake/exhaust valves. They have Manley springs good to .650 lift with titanium retainers, hardened locks and small diameter valve seals. Flow numbers from GMHighTechPerformance.com posted
Lift Intake Exhaust
0.100 72 63
0.200 148 126
0.300 212 162
0.400 264 189
0.500 302 205
0.600 322 214
0.700 316 221
$800 WITH the spring upgrade and mill job
-Bare L76 Intake $300
-Nick Williams 90mm Throttle Body $375
-L76 fuel rails with LS7 injectors $100
-SLP Lid with new K&N $110
*L76 intake, throttle body, lid, filter, bellow, rails and injectors for $750*
-SLP 1 3/4in long tube headers $300
-SLP off road Y-pipe with 3inch piping to the rear of car $200
-Brand New 3 chamber Magnaflow muffler $75
*Full exhaust from headers to muffler for $475*
FMVB 4L80 transmission
-over $2800 in new internal parts not counting $1000 core and labor
-upgraded O/D planet, over run drum, center support, rear ring gear, Red Eagle HD kit with all Red Eagle frictions and Kolene steels, direct and intermediate Powerpacks, Red Eagle Rear Band, Red Eagle Front Band, upgraded sprag, Stage 3 transgo full manual valve body kit.
$2200
Yank 4L80e conversion cross member w/ tq arm mount $160
TCI TH400 Slip Yoke $70
Precision Industries (Vigilante) 3-disc 9.5in lock up converter
-for 4L80e to LSx conversion, stall speed is 3600. I will include TCI flexplate $1000 new $800
I will sell the entire transmission, stall converter and everything needed for the swap for $3000
New GM 10 bolt with 20,000 documented miles. Posi-trac, 2.73 gears, no whine, works perfectly. $600
Brand new, uninstalled Koni SA rear struts, bought them on sale from Strano but car wrecked before I could install them $200 for both
-2 ebony Trans Am door panels, leather, NO cracks, power windows/locks, I will include all trim pieces associated with door panels $230
-ebony AC vents (pair) $40
-ebony radio bezel $30
-ebony lower center console $100
-ebony top section center console for an automatic $100
$150 for both sections
-Camaro ebony dash (not portion under windshield, that is cracked) $100
-ebony carpet great condition $120
-T-tops $200 for the set
-gauge surround bezel (ebony) $40
-ebony backseat panels $100 for the pair
-ebony hatch speaker panels $70 for the pair
-non projector style, black Halo headlights $100 for both
-6000k HID low beams $100
-6000k HID high beams $100
-1998 taillights permanently tinted with Niteshades (light goes through fine) $100 for both
*Please PM me with anything you need, I have an entire 1998 Camaro to part out
*Paypal preferred but money order's fine too
*Buyer is responsible for shipping and 3% Paypal fees
*Prices are OBO but no lowballers please
*You can buy the entire car from me if you feel like messing with replacing the rear clip for $12,000 cash.
The car is a 1998 Z28 and is Sebring Silver in color. The interior is ebony. I am located in Owasso, Oklahoma. Verified Paypal with plenty of history/feedback on this site. The motor, transmission, and rear end are fully documented. They were assembled and installed by professionals and are in absolutely perfect condition.
If you feel inclined to repair the rear end on this car and have an outstanding vehicle you can purchase it from me for $12,000 OBO. I am also open to trades/partial trades on a sportbike 600cc and up, decent daily driver or 4 wheel drive vehicle.
Pictures will be up ASAP.
SDPC built LS2 based 402 stroker with less than 7500 miles since install
Parts list:
-GM LS2 aluminum block
-GM bell housing dowels,
-GM head dowels,
-GM main bolts,
-Durabond cam bearings,
-GM drain plug, dumbell plug and drain plugs,
-Clevite main bearings,
-Eagle crankshat,
-Skat connecting rods,
-Clevite rod bearings,
-Manley pistons (-12cc),
-Total Seal Piston rings,
-SDPC Timing Set,
-Katech Sensor Harness,
-Manley pushrods,
-LS7 oil pump and LS7 lifters,
-.040 Cometic head gasket set,
-ARP head bolts
-GM Valley cover
$7000+ new from SDPC with receipts, asking $5000 buyer pays shipping and paypal fees
*I can supply all parts numbers of parts used from SDPC receipts as well as full SDPC and professional installation*
Full Assembled L92 heads
-milled to 62cc chamber from the factory 70cc for a bump in compression. I believe they can be milled down to 59cc if desired but I am not certain. They have the GM 2.16/1.59 intake/exhaust valves. They have Manley springs good to .650 lift with titanium retainers, hardened locks and small diameter valve seals. Flow numbers from GMHighTechPerformance.com posted
Lift Intake Exhaust
0.100 72 63
0.200 148 126
0.300 212 162
0.400 264 189
0.500 302 205
0.600 322 214
0.700 316 221
$800 WITH the spring upgrade and mill job
-Bare L76 Intake $300
-Nick Williams 90mm Throttle Body $375
-L76 fuel rails with LS7 injectors $100
-SLP Lid with new K&N $110
*L76 intake, throttle body, lid, filter, bellow, rails and injectors for $750*
-SLP 1 3/4in long tube headers $300
-SLP off road Y-pipe with 3inch piping to the rear of car $200
-Brand New 3 chamber Magnaflow muffler $75
*Full exhaust from headers to muffler for $475*
FMVB 4L80 transmission
-over $2800 in new internal parts not counting $1000 core and labor
-upgraded O/D planet, over run drum, center support, rear ring gear, Red Eagle HD kit with all Red Eagle frictions and Kolene steels, direct and intermediate Powerpacks, Red Eagle Rear Band, Red Eagle Front Band, upgraded sprag, Stage 3 transgo full manual valve body kit.
$2200
Yank 4L80e conversion cross member w/ tq arm mount $160
TCI TH400 Slip Yoke $70
Precision Industries (Vigilante) 3-disc 9.5in lock up converter
-for 4L80e to LSx conversion, stall speed is 3600. I will include TCI flexplate $1000 new $800
I will sell the entire transmission, stall converter and everything needed for the swap for $3000
New GM 10 bolt with 20,000 documented miles. Posi-trac, 2.73 gears, no whine, works perfectly. $600
Brand new, uninstalled Koni SA rear struts, bought them on sale from Strano but car wrecked before I could install them $200 for both
-2 ebony Trans Am door panels, leather, NO cracks, power windows/locks, I will include all trim pieces associated with door panels $230
-ebony AC vents (pair) $40
-ebony radio bezel $30
-ebony lower center console $100
-ebony top section center console for an automatic $100
$150 for both sections
-Camaro ebony dash (not portion under windshield, that is cracked) $100
-ebony carpet great condition $120
-T-tops $200 for the set
-gauge surround bezel (ebony) $40
-ebony backseat panels $100 for the pair
-ebony hatch speaker panels $70 for the pair
-non projector style, black Halo headlights $100 for both
-6000k HID low beams $100
-6000k HID high beams $100
-1998 taillights permanently tinted with Niteshades (light goes through fine) $100 for both
*Please PM me with anything you need, I have an entire 1998 Camaro to part out
*Paypal preferred but money order's fine too
*Buyer is responsible for shipping and 3% Paypal fees
*Prices are OBO but no lowballers please
*You can buy the entire car from me if you feel like messing with replacing the rear clip for $12,000 cash.
Last edited by SVT THIS; 04-13-2009 at 05:43 AM. Reason: update