2000 Corvette 6 Speed LS1 Rolling Driveline Complete C5
09-22-2009, 10:27 AM
#1
Closed ex-Sponsor Account
Thread Starter
iTrader: (6)
Join Date: Jan 2006
Location: Columbia Station, OH
Posts: 42
Likes: 0
Received 0 Likes
on
0 Posts
2000 Corvette 6 Speed LS1 Rolling Driveline Complete C5 CLEVELAND PICK A PART IS PROUD TO OFFER THIS 2000 CHEVROLET CORVETTE ROLLING CHASSIS!
THIS CHASSIS FEATURES A 5.7L LS1 ENGINE AND 6-SPEED MANUAL TRANSMISSION!
This engine pumps out 345 HP @ 5,600 RPM and 350 LB-FT of torque @ 4,400 RPM!
This chassis will include:
2000 Chevrolet Corvette 5.7L 350 HP LS1 engine
6-speed manual transmission
Complete front and rear suspensions
3.42 rear differential
Floor shifter
LH and RH fuel tanks and fuel pumps
OEM exhaust
Charcoal canister
Fuel crossover pipe
Complete anti-lock brake system with booster and module
Engine computer and engine harness
Transmission harness
Throttle control module
Complete Body harness to help get your project started
OEM key w/ computer
Air flow meter
Pedals
Brake lines and fuel lines
Steering column with tilt wheel
Leather wrapped steering wheel (no air bag)
18 Inch C5 Thin Spoke Wheels (Polished) With Tires
This package has only 49k miles!
Here is the VIN from this Corvette: 1G1YY22GXY5128383
At Cleveland Pick A Part we thoroughly inspect each motor and transmission and then back it with our exclusive 6 month warranty!
Before we start each engine, we remove all the spark plugs and hand turn the engine over to make sure no oil has passed the rings.
We do a compression test to make sure the rings, valves, and head gaskets are properly sealed.
We do a vacuum test to make sure there are no burned or sticking valves, collapsed lifters, or vacuum leaks.
We do a oil pressure test at cold start up and warm operating temperature to ensure proper bearing clearance, that there are no restrictions in the oiling system, and that there are no exhaust gases in the cooling system.
We inspect the manual transmission by draining the fluid and inspecting the fluid and magnets for any debris or contamination. We then refill the transmission with new fluid and run test it through all of the gears to ensure it shifts properly. If any problems are found, the transmission will be torn down for inspection and repaired as necessary.
Compression was a TIGHT 200 over 165: 1-200 2-185 3-180 4-170 5-195 6-170 7-180 8-165
Oil pressure was 50 pounds cold and 40 pounds warm
Vacuum was a SOLID 17 inches
CO check pass
Price: 6750.00 + Shipping
Call Tom at 866-236-5031
THIS CHASSIS FEATURES A 5.7L LS1 ENGINE AND 6-SPEED MANUAL TRANSMISSION!
This engine pumps out 345 HP @ 5,600 RPM and 350 LB-FT of torque @ 4,400 RPM!
This chassis will include:
2000 Chevrolet Corvette 5.7L 350 HP LS1 engine
6-speed manual transmission
Complete front and rear suspensions
3.42 rear differential
Floor shifter
LH and RH fuel tanks and fuel pumps
OEM exhaust
Charcoal canister
Fuel crossover pipe
Complete anti-lock brake system with booster and module
Engine computer and engine harness
Transmission harness
Throttle control module
Complete Body harness to help get your project started
OEM key w/ computer
Air flow meter
Pedals
Brake lines and fuel lines
Steering column with tilt wheel
Leather wrapped steering wheel (no air bag)
18 Inch C5 Thin Spoke Wheels (Polished) With Tires
This package has only 49k miles!
Here is the VIN from this Corvette: 1G1YY22GXY5128383
At Cleveland Pick A Part we thoroughly inspect each motor and transmission and then back it with our exclusive 6 month warranty!
Before we start each engine, we remove all the spark plugs and hand turn the engine over to make sure no oil has passed the rings.
We do a compression test to make sure the rings, valves, and head gaskets are properly sealed.
We do a vacuum test to make sure there are no burned or sticking valves, collapsed lifters, or vacuum leaks.
We do a oil pressure test at cold start up and warm operating temperature to ensure proper bearing clearance, that there are no restrictions in the oiling system, and that there are no exhaust gases in the cooling system.
We inspect the manual transmission by draining the fluid and inspecting the fluid and magnets for any debris or contamination. We then refill the transmission with new fluid and run test it through all of the gears to ensure it shifts properly. If any problems are found, the transmission will be torn down for inspection and repaired as necessary.
Compression was a TIGHT 200 over 165: 1-200 2-185 3-180 4-170 5-195 6-170 7-180 8-165
Oil pressure was 50 pounds cold and 40 pounds warm
Vacuum was a SOLID 17 inches
CO check pass
Price: 6750.00 + Shipping
Call Tom at 866-236-5031
