FS: LT1 Performance Parts (heads,intake,etc)
11-28-2004 | 01:31 AM
#1
Thread Starter
Teching In
Joined: Dec 2002
Posts: 12
Likes: 0
From: Fort Washington,MD
FS: LT1 Performance Parts (heads,intake,etc) -Cartek Stage 3 CNC Ported Heads. These have about 2000 miles on them and went 11.4's on motor in a 93 Vette. I bought AFR 220's and no longer need these.
Specs:
-Milled to give 11:1 compression ratio on stock motor
-Comp Cams Springs good to .550 lift
-Polished CC's
-Ferrea Valves 2.02 / 1.56
-NO rocker studs
$900 shipped
-93 CNC ported intake and fuel rail, $125 shipped
-Corsa Exhaust w/ Fully Polished Tips, $600
-Holley 52mm Throttle Body, CNC'd Billet Aluminum, Polished $300 shipped
-28# Flowmatched Injectors from TPIS, $200 shipped
-LS1 Aluminum Driveshaft $150
-BMR Torque Arm, red, $250
-Spohn Lower Control Arms, red, $90
-Spohn Panhard Rod $50
-95 Trans Am rear w/ 373 gears and all new bearings, ABS,No TCS,
1500 miles since install $300
I have pics of the heads/intake and I can get pics of anything else also. My email ischronicly@aol.com and everything is located in Maryland, right outside D.C.
Nick
Specs:
-Milled to give 11:1 compression ratio on stock motor
-Comp Cams Springs good to .550 lift
-Polished CC's
-Ferrea Valves 2.02 / 1.56
-NO rocker studs
$900 shipped
-93 CNC ported intake and fuel rail, $125 shipped
-Corsa Exhaust w/ Fully Polished Tips, $600
-Holley 52mm Throttle Body, CNC'd Billet Aluminum, Polished $300 shipped
-28# Flowmatched Injectors from TPIS, $200 shipped
-LS1 Aluminum Driveshaft $150
-BMR Torque Arm, red, $250
-Spohn Lower Control Arms, red, $90
-Spohn Panhard Rod $50
-95 Trans Am rear w/ 373 gears and all new bearings, ABS,No TCS,
1500 miles since install $300
I have pics of the heads/intake and I can get pics of anything else also. My email ischronicly@aol.com and everything is located in Maryland, right outside D.C.
Nick
11-28-2004 | 08:29 PM
#2
Originally Posted by Project_LT1
-Cartek Stage 3 CNC Ported Heads. These have about 2000 miles on them and went 11.4's on motor in a 93 Vette. I bought AFR 220's and no longer need these.
Specs:
-Milled to give 11:1 compression ratio on stock motor
-Comp Cams Springs good to .550 lift
-Polished CC's
-Ferrea Valves 2.02 / 1.56
-NO rocker studs
$900 shipped
-93 CNC ported intake and fuel rail, $125 shipped
-Corsa Exhaust w/ Fully Polished Tips, $600
-Holley 52mm Throttle Body, CNC'd Billet Aluminum, Polished $300 shipped
-28# Flowmatched Injectors from TPIS, $200 shipped
-LS1 Aluminum Driveshaft $150
-BMR Torque Arm, red, $250
-Spohn Lower Control Arms, red, $90
-Spohn Panhard Rod $50
-95 Trans Am rear w/ 373 gears and all new bearings, ABS,No TCS,
1500 miles since install $300
I have pics of the heads/intake and I can get pics of anything else also. My email ischronicly@aol.com and everything is located in Maryland, right outside D.C.
Nick
Specs:
-Milled to give 11:1 compression ratio on stock motor
-Comp Cams Springs good to .550 lift
-Polished CC's
-Ferrea Valves 2.02 / 1.56
-NO rocker studs
$900 shipped
-93 CNC ported intake and fuel rail, $125 shipped
-Corsa Exhaust w/ Fully Polished Tips, $600
-Holley 52mm Throttle Body, CNC'd Billet Aluminum, Polished $300 shipped
-28# Flowmatched Injectors from TPIS, $200 shipped
-LS1 Aluminum Driveshaft $150
-BMR Torque Arm, red, $250
-Spohn Lower Control Arms, red, $90
-Spohn Panhard Rod $50
-95 Trans Am rear w/ 373 gears and all new bearings, ABS,No TCS,
1500 miles since install $300
I have pics of the heads/intake and I can get pics of anything else also. My email ischronicly@aol.com and everything is located in Maryland, right outside D.C.
Nick
Any flow numbers on the heads?
