Are LT1's internally ballanced?
#2
The crank is balanced for the lightweight hypereutectic pistons, but the entire rotating assembly itself is externally counter-balanced at the flywheel. Front hub/dampner is neutrally balanced.
#4
What brand flywheel are you running?
Yes, it is recommended to have the new parts matched to the imbalance of the factory pieces, in hopes of lessening the chance of a vibration issue (not only uncomfortable, but can cause premature main bearing wear/damage). The trick is finding a machine shop that can do this for you.
Some people have gotten lucky without balancing, which may be in-part due to the loose tolerances of stock specifications. You'll find a small weight cast into the back of the stock flywheel -- the same flywheel that is used in all 93-97 LT1's...
Yes, it is recommended to have the new parts matched to the imbalance of the factory pieces, in hopes of lessening the chance of a vibration issue (not only uncomfortable, but can cause premature main bearing wear/damage). The trick is finding a machine shop that can do this for you.
Some people have gotten lucky without balancing, which may be in-part due to the loose tolerances of stock specifications. You'll find a small weight cast into the back of the stock flywheel -- the same flywheel that is used in all 93-97 LT1's...
#6
Launching!
iTrader: (3)
Join Date: Feb 2004
Location: BURLESON TX
Posts: 290
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Alex94TAGT
What brand flywheel are you running?
Yes, it is recommended to have the new parts matched to the imbalance of the factory pieces, in hopes of lessening the chance of a vibration issue (not only uncomfortable, but can cause premature main bearing wear/damage). The trick is finding a machine shop that can do this for you.
Some people have gotten lucky without balancing, which may be in-part due to the loose tolerances of stock specifications. You'll find a small weight cast into the back of the stock flywheel -- the same flywheel that is used in all 93-97 LT1's...
Yes, it is recommended to have the new parts matched to the imbalance of the factory pieces, in hopes of lessening the chance of a vibration issue (not only uncomfortable, but can cause premature main bearing wear/damage). The trick is finding a machine shop that can do this for you.
Some people have gotten lucky without balancing, which may be in-part due to the loose tolerances of stock specifications. You'll find a small weight cast into the back of the stock flywheel -- the same flywheel that is used in all 93-97 LT1's...
but how do you like the Delteq system, and how long have you had it.
Brentt
Oh, and what took you so long to join LS1tech?
Welcome to the site
#7
12 Second Club
iTrader: (1)
Join Date: Dec 2003
Location: Cleveland, Georgia
Posts: 3,027
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by BRENTT94Z
Not to get off subject
but how do you like the Delteq system, and how long have you had it.
Brentt
Oh, and what took you so long to join LS1tech?
Welcome to the site
but how do you like the Delteq system, and how long have you had it.
Brentt
Oh, and what took you so long to join LS1tech?
Welcome to the site
Trending Topics
#8
TECH Fanatic
iTrader: (1)
I'm pretty confused on this whole internal/external balance thing now. I thought that I understood, but I think I am more confused now. I purchased a new Cola 3.50 inch stroke 4340 forged steel crank for SBC 1 piece rear seal. It is a 350 main and is going to be used in a forced induction buildup for my LT1. It does not state whether or not it is internal or external balance and I thought that all 1 piece rear seal cranks were internal. I am going to use an ATI Super Damper and a steel flywheel Street Twin clutch assembly. So, is this going to be an internal or external balance or, like I have heard before, can you do either type of balance and which is better? I have heard that the internal is more expensive though.
#9
if you are going to be really spinning your car up then have everything sent to the balancer for balancing. thats the rotating assembly and botht he flywheel and hub/balancer. or if you just want it balanced send the rotating assembly and have it balanced. then you should be able to use a neutral balance flywheel too. at least i think thats right
#10
TECH Fanatic
iTrader: (1)
Ok, I am just getting the parts together and I am going to have the long block professionally built. I was planning on sending the ATI Super Damper and the Street twin to have everything balanced when it is built. I probably won't be spinning it past about 6,800, but I want the thing built right!
#11
On The Tree
Join Date: Jan 2004
Location: Houston/ Austin, TX
Posts: 188
Likes: 0
Received 0 Likes
on
0 Posts
The stock motor is counterbalanced at the flywheel.
If you are going with a rebuild, have it neutrally balanced and get a neutrally balanced flywheel and an SFI crank.
If you are going with a rebuild, have it neutrally balanced and get a neutrally balanced flywheel and an SFI crank.
#12
You can balance it externally which means the machine shop should take your front damper, and your flywheel and balance it all at the flywheel.
You can do internally which means they just need the crank/rods/pistons. Its then up to you do make sure your flywheel is also zero balanced. This way they may need to add heavy metal to your crank which is $$$, but its the better way to do things.
You can do internally which means they just need the crank/rods/pistons. Its then up to you do make sure your flywheel is also zero balanced. This way they may need to add heavy metal to your crank which is $$$, but its the better way to do things.
#15
Sounds like I'm in trouble? I have a stock bottom end with a yank 3600. Gave it the gas the other day and it seems the weight attached to the flexplate sheared off, ending up in my dustpan. I'm getting a very noticeable vibration now. Scared to drive it bad.... I cannot just throw a new TCI flexplate on there can I?
#16
Village Troll
iTrader: (2)
Sounds like I'm in trouble? I have a stock bottom end with a yank 3600. Gave it the gas the other day and it seems the weight attached to the flexplate sheared off, ending up in my dustpan. I'm getting a very noticeable vibration now. Scared to drive it bad.... I cannot just throw a new TCI flexplate on there can I?
#18
TECH Regular
Join Date: Apr 2007
Location: Kempner, TX
Posts: 420
Likes: 0
Received 0 Likes
on
0 Posts
We sometimes refer to them as hybrids, just like the L98s. Neutral at the damper/balancer but counter-weighted at the flex-plate/flywheel.
". . . it seems the weight attached to the flexplate sheared off . . .", did it?
Jake
". . . it seems the weight attached to the flexplate sheared off . . .", did it?
Jake