chips
chips are there any really good chips out there to boost hp? i was reading aobut the hypertech 1 i think it was, it was supose to help gas millage a little, altohugh i looknig mroe for power and tunning. does anybody know of a good 1 and where i can order it from?
I'd do at least the basic bolt ons before altering the PCM.
(Cold air intake + nice flowing 3" catback)
If I remember correctly, your car will require that you send the whole PCM in.
It's easy to do, but it leaves the car undrivable for a week or so while it's out.
Remove two 10mm bolts at the base, then unplug the pigtails.
(I don't think any of the mail order guys do core exchanges)
Older PCMs let you remove the chip from the PCM and swap it.
(Cold air intake + nice flowing 3" catback)
If I remember correctly, your car will require that you send the whole PCM in.
It's easy to do, but it leaves the car undrivable for a week or so while it's out.
Remove two 10mm bolts at the base, then unplug the pigtails.
(I don't think any of the mail order guys do core exchanges)
Older PCMs let you remove the chip from the PCM and swap it.
k yeah ill see later this summer i guess, i still might do headers later on, i have a slp cai, the tf 90degree elbow, and the slp lm2 catback which is 3" need headers and a y pipe though then ill probobly get it tunned
Trending Topics
Yup, a lot of guys wait until they have a few bigger mods then go have it tuned on a dyno chassis.
Which actually works out well since it's set up perfectly for your car.
Assuming there is a decent tuner in your area.
(FWIW, I drove mine 4hrs to Tulsa to have Ed Wright tune it because I trust him to do it right)
Headers are an awesome mod for LT1s. (actually for just about any car)
If you can get away with it in your state, go with long tubes.
Which actually works out well since it's set up perfectly for your car.
Assuming there is a decent tuner in your area.
(FWIW, I drove mine 4hrs to Tulsa to have Ed Wright tune it because I trust him to do it right)
Headers are an awesome mod for LT1s. (actually for just about any car)
If you can get away with it in your state, go with long tubes.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Originally Posted by James Montigny
Yup, a lot of guys wait until they have a few bigger mods then go have it tuned on a dyno chassis.
Which actually works out well since it's set up perfectly for your car.
Assuming there is a decent tuner in your area.
(FWIW, I drove mine 4hrs to Tulsa to have Ed Wright tune it because I trust him to do it right)
Headers are an awesome mod for LT1s. (actually for just about any car)
If you can get away with it in your state, go with long tubes.
Which actually works out well since it's set up perfectly for your car.
Assuming there is a decent tuner in your area.
(FWIW, I drove mine 4hrs to Tulsa to have Ed Wright tune it because I trust him to do it right)
Headers are an awesome mod for LT1s. (actually for just about any car)
If you can get away with it in your state, go with long tubes.
