. Amazing Job, I'll try to post pics later tonight. 
LT1 Alternator/PS kit
Well I had to take pictures again (these are not as good), but they show what is needed. I will say I am taking a few things to the powdercoater tomarrow and hopfully by the end of the week I will have the motor fully assembled with some high quality day time pics (instead of at night with my shop lights)
This is what I have to say about the kit. The polish parts are awesome, you can see your reflection so well you could comb your hair, lol. The entire kit comes with full detailed instructions with individual bags and pictures showing where exactly everything goes, so in a sense its idiot proof. I didn't have to modify anything as everything bolted right up. This is by far the best kit around and I have seen several pieces over the years and not one comes close to matching this one.
For you drag racing guys, this kit is light, lighter than the factory aluminum piece that comes on the cars from the factory, plus its much better looking
.
The alternator hangs about as low as the LS1 f-body, maybe even higher, but not lower. So don't wory about water damage or anything. The power steering pulley setup is close to the waterpump (I'll get a pic) but there is definatly enough room not to have to modify anything, in fact even after powdercoating it will be fine. The tensioner setup (by the valvecover) is really easy to use, stick a 3/8 socket inside it and turn to loosen or apply tension.
Well here are the pics (Larry I plan on getting some really good pics when the motor is completely finished so stay tuned).
Thanks again Speed Inc for making the kit
This is what I have to say about the kit. The polish parts are awesome, you can see your reflection so well you could comb your hair, lol. The entire kit comes with full detailed instructions with individual bags and pictures showing where exactly everything goes, so in a sense its idiot proof. I didn't have to modify anything as everything bolted right up. This is by far the best kit around and I have seen several pieces over the years and not one comes close to matching this one.
For you drag racing guys, this kit is light, lighter than the factory aluminum piece that comes on the cars from the factory, plus its much better looking
.The alternator hangs about as low as the LS1 f-body, maybe even higher, but not lower. So don't wory about water damage or anything. The power steering pulley setup is close to the waterpump (I'll get a pic) but there is definatly enough room not to have to modify anything, in fact even after powdercoating it will be fine. The tensioner setup (by the valvecover) is really easy to use, stick a 3/8 socket inside it and turn to loosen or apply tension.
Well here are the pics (Larry I plan on getting some really good pics when the motor is completely finished so stay tuned).
Thanks again Speed Inc for making the kit
Last edited by T/A KID; Jul 7, 2008 at 12:03 AM.
Thanks Paul, I figure the only way stuff will get done is to do it. Shannon helped me out today on the build so that helped.
Next thing is to powerwash and to pull the dash, not looking for to it, lol.
Next thing is to powerwash and to pull the dash, not looking for to it, lol.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
How about the belt routing for the procharger?
that's a f'n shiney trans though... lol. Nice setup!!
alternator relocation only I just received confirmation that we will have pics and prices by Friday.
& kits to ship by Monday
price is not set in stone yet, but thinking around
$250 shipped ( polished )
$215 shipped ( satin )
& kits to ship by Monday
price is not set in stone yet, but thinking around
$250 shipped ( polished )
$215 shipped ( satin )
Joined: Nov 2001
Posts: 10,023
Likes: 6
From: LT1 land...the "409" of the 90s!
$435 polished
$400 Satin
ALT only ( prices below will be confirmed Friday )
$250ish polished
$215ish satin
prices include shipping to the Cont. US
Joined: Nov 2001
Posts: 10,023
Likes: 6
From: LT1 land...the "409" of the 90s!