minnesota peeps check in!!!
05-05-2006, 08:51 AM
#161
On The Tree
iTrader: (1)
Join Date: Nov 2002
Location: Prior Lake, Minnesota
Posts: 107
Likes: 0
Received 0 Likes
on
0 Posts
Dyno If enough of you are interested, it'll be around $75.00 for three pulls, also LS-1 tuning is available on the dyno. Anything from stock to full mod, let me know. Dyno will be at my place in Prior Lake. most likely Sunday morning. dyno will not show up to late Sat night. It gets a little noise to run after 9-10pm.
Let me know,
Cory
Let me know,
Cory
05-05-2006, 09:23 AM
#162
Originally Posted by BONESTOCKC5
If enough of you are interested, it'll be around $75.00 for three pulls, also LS-1 tuning is available on the dyno. Anything from stock to full mod, let me know. Dyno will be at my place in Prior Lake. most likely Sunday morning. dyno will not show up to late Sat night. It gets a little noise to run after 9-10pm.
Let me know,
Cory
Let me know,
Cory
05-05-2006, 09:50 AM
#164
On The Tree
iTrader: (1)
Join Date: Nov 2002
Location: Prior Lake, Minnesota
Posts: 107
Likes: 0
Received 0 Likes
on
0 Posts
Dynotune from watertown, South Dakota, Andy is going to be at my place. VERY good tuning, He does all my friends tuning on the dyno, also very good with driveability. My 427 averages 29mpg on the highway. not bad for 537rwhp/517rwtq. daily driver. If there is enough interest dyno price will be better. just looking to have some fun with the cars, same dyno, same place, #'s don't lie
05-05-2006, 12:43 PM
#166
12 Second Club
iTrader: (8)
Join Date: Jul 2004
Location: Vancouver, BC
Posts: 708
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by BONESTOCKC5
If enough of you are interested, it'll be around $75.00 for three pulls, also LS-1 tuning is available on the dyno. Anything from stock to full mod, let me know. Dyno will be at my place in Prior Lake. most likely Sunday morning. dyno will not show up to late Sat night. It gets a little noise to run after 9-10pm.
Let me know,
Cory
Let me know,
Cory
Would there be tuning hardware there for use, i.e. wideband's or loggers?
I've got HPT licensed and a laptop, but no EIO or any WB02's yet.
Would they have any of that stuff availible for some pulls that I could log and work with on my own?
Not sure if that's allowed, im new at the tuning thing and have never had a dyno.
DJ
05-05-2006, 08:17 PM
#167
Ahhhhhhh............that felt good. I went down to porky's for a little bit and then left. Coming home some WRX pulls along side of me with his woman, I give her a little rev and he laughs....................then for some reason...........he started to fade in the rear view mirror....110....120...140.... he finally caught back up when I slowed down. Kept his face looking straight 
so did his woman
I love torque. Only had to take her to about 5K rpms to pull away steadily.
so did his woman I love torque. Only had to take her to about 5K rpms to pull away steadily.
05-25-2006, 12:29 PM
#172
10 Second Club
iTrader: (15)
Join Date: Nov 2001
Location: St. Michael, MN.
Posts: 4,519
Likes: 0
Received 0 Likes
on
0 Posts
Wohoo! Got the new FLT Stage IV trans and Yank PT4000 installed and have put 185 miles on the car. I'm working on the tune and have gotten it to idle pretty good so far, just needs some tweaks on cold starts. I also need a front end alignment as well, but overall I am very happy to finally have this money pit running after so long. I can't believe it took this long (the tear down started in Nov-04).
05-25-2006, 04:43 PM
#175
Staging Lane
Join Date: May 2002
Location: Twin Cities, MN.
Posts: 55
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 99whitews6
intrigued...................tell me more.
05-25-2006, 06:01 PM
#176
Originally Posted by DrkPhx
Wohoo! Got the new FLT Stage IV trans and Yank PT4000 installed and have put 185 miles on the car. I'm working on the tune and have gotten it to idle pretty good so far, just needs some tweaks on cold starts. I also need a front end alignment as well, but overall I am very happy to finally have this money pit running after so long. I can't believe it took this long (the tear down started in Nov-04).
