CLARKSLS1SS

iTrader: (23)

goodrich where you doing your install at? Maybe i can swing by

DarkFormula

iTrader: (80)

Hell Ben, you can do it for him

BTW, we're changing COFBA this year into something bigger. CR is growing as well, so I'll keep people updated. But right now, the real-time events are through CR, so if you're not a member or are a lurker, get back over there and that way you'll be up-to-date on ****.

poncho2001

iTrader: (3)

I'm in Dayton, and have relatives in Grove City.

DarkFormula

iTrader: (80)

I feel sorry for ya

CLARKSLS1SS

iTrader: (23)

Hell yeah i'd definetly give him a hand, but he never got back on here,lol

casey02ws6

iTrader: (2)

Man this weather sucks. I offered to help him with the LT install when it warmed up a bit. I wonder if he decided to go ahead and knock it out.

I have a clutch install staring me in the face 0- not looking forward to that!

Necron

iTrader: (11)

Canton Ohio here few hours north of columbus.

It should start warming up soonish, at leats i hope.

goodrich969

iTrader: (9)

Hey fellas... sorry i havent been on this thread alot... I worked 68 hours last week. I plan on doing LTs,x pipe with dumped spiral flows and !air/!egr all in the same day. Id appreciated help from anyone. I have a nice two car garage me and my friend work on our project camaro in that could be used most likely.

blk~2000~Z28

I read in your sig that you have an LT1, I did LT's, !EGR / !AIR, Y pipe on my LS1 and it wasn't hard just time consuming. It would have been shorter had I trusted my friend and not checked all of his work. You would definently benefit from someone fitting up and tightening the headers but other than that you could do it yourself.

goodrich969

iTrader: (9)

yeah but id really like to have someone around that knows how to do it with ease just for piece of mind, ya kno?

CLARKSLS1SS

iTrader: (23)

Check your pm goodrich969

blk~2000~Z28

I can't fault you there. I wouldn't have finished getting my headers into position as quick as I did w/o my buddy. I would recommend header bolts with a taper like the stockers or just reuse the stockers, I had a couple of bolts almost get cross threaded. The biggest pain on my install had to be the fitment of the y-pipe which you shouldn't have considering your setup. I also did my install without removing my coil packs and that I would change if I did it all over again.

DarkFormula

iTrader: (80)

It's almost easier to remove the tranny to do headers. I had mine done in 10 minutes with the tranny out

TimTaylor75

iTrader: (4)

In that case, when the time comes to install headers, I'll just do it without the tranny or motor in place.

Oh wait, neither of them are in the car right now anyways.

goodrich969

iTrader: (9)

bump...

lawnman

Any of you Columbus guys want to get together for a track day at NTR?

goodrich969

iTrader: (9)

That sounds good, I just have to get my headers and x pipe on and buy my radials.

lawnman

If you want the practice you could always install my headers and duals. Just a thought.
Should we try for a Wed. night or a Friday night?

goodrich969

iTrader: (9)

I dont know right now. Wensday/friday.. are you talking about NTR? Im going only after I get my headers and **** installed and I get my radials. I want my first visit to be a good one.

lawnman

I think NTR is does not open until April. Would that be enough time? I would also like to do the exhaust before I go, but I still have to install sfc and a loop.