My switch panel and micro edge

Reply Subscribe

Thread Tools

Search this Thread

Oct 16, 2009 | 10:23 PM

#21

SHovV

TECH Resident

iTrader: (1)

Joined: May 2008

Posts: 937

Likes: 2

From: Rockport, TX

Quote:

Originally Posted by rmata

And I was just joking around with the slow and fast. That switch will be to toggle between N/A and N2O timing.

thats a cool idea for the 2 diff. timing modes

Oct 18, 2009 | 10:30 AM

#22

YURVIEW

11 Second Club

iTrader: (127)

Joined: Jun 2002

Posts: 984

Likes: 0

From: MS

Quote:

Originally Posted by rmata

The wire harness clicks in on the backside and isn't visible at all

How did you do this???

Oct 18, 2009 | 09:34 PM

#23

rmata

Thread Starter

TECH Regular

iTrader: (34)

Joined: Mar 2004

Posts: 423

Likes: 0

From: Corpus Christi, TX

Quote:

Originally Posted by YURVIEW

How did you do this???

I undid the four screws to take the housing apart. Then I measured and cut out the plastic so that I could put the backside in the back of the panel and the frontside in the front, and then screw them back together which locks it into the plastic. The screws don't go through the panel, it's just the little lip that goes all the way around the microedge that clamp it in place.

Jan 28, 2010 | 09:25 AM

#24

Beer99C5

TECH Addict

iTrader: (21)

Joined: Nov 2005

Posts: 2,209

Likes: 0

From: Maine USA

Here is a beta F-Body Radio/HVAC Delete Beer Panel with Microedge

Wish the MicroEdge plugged into the back vs the side...Had to dremel the back of the panel a bit...

Jan 28, 2010 | 09:48 AM

#25

Nick@HSW

FormerVendor

iTrader: (4)

Joined: Jul 2005

Posts: 1,954

Likes: 0

From: Glenolden, PA

Quote:

Originally Posted by Beer99C5

Here is a beta F-Body Radio/HVAC Delete Beer Panel with Microedge

Wish the MicroEdge plugged into the back vs the side...Had to dremel the back of the panel a bit...

Is this going to NASA? Looks good.

Nick

Jan 28, 2010 | 04:07 PM

#26

Zero4488

Restricted User

iTrader: (10)

Joined: Feb 2007

Posts: 1,455

Likes: 0

From: Jersey

Change the fast/slow switch to the Go/ "GO BABY GO" switch

Jan 28, 2010 | 05:09 PM

#27

Nsty98LS1

11 Second Club

iTrader: (11)

Joined: Jan 2004

Posts: 469

Likes: 0

From: Gallitzin, Pa

where are you guys getting the plastic to make these delete panels? i've been trying to find it locally, but with no luck.

Jan 28, 2010 | 05:18 PM

#28

daschra79

On The Tree

iTrader: (2)

Joined: Nov 2009

Posts: 158

Likes: 0

From: St. Louis area

Quote:

Originally Posted by Nsty98LS1

where are you guys getting the plastic to make these delete panels? i've been trying to find it locally, but with no luck.

Just looks like ABS plastic. Do a search on google and you should be able to find some.

LS1 Tech Stories

The Best V8 Stories One Small Block at Time

Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?

Pouria Savadkouei

Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine

Verdad Gallardo

7 Most Reliable High-Performance Engines GM Has Ever Built

Verdad Gallardo

Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin

Verdad Gallardo

6 Common C5 Corvette Failures and What's Involved In Repairing Them

Pouria Savadkouei

Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph

Verdad Gallardo

Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked

Pouria Savadkouei

Top 10 Most Powerful Chevy Trucks Ever Made!

Hennessey's New Supercharged Silverado ZR2 Has 700 HP

Verdad Gallardo

Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes

Verdad Gallardo

Jan 28, 2010 | 07:08 PM

#29

o2bird

Staging Lane

Joined: Jun 2004

Posts: 60

Likes: 0

From: peoria, arizona

Quote:

Originally Posted by Nick@HSW

Is this going to NASA?

Nope, my car. Should look pretty sick with my 6LE 4 gauge panel where the vents go. Thanks again Jim

Jan 28, 2010 | 07:56 PM

#30

BayAreaSS

TECH Veteran

iTrader: (10)

Joined: May 2006

Posts: 4,240

Likes: 2

From: Bay Area, CA (Pittsburg)

That looks clean. I also use the IAT timing trick to reduce timing. It works good and easy to do

Jan 28, 2010 | 09:17 PM

#31

Beer99C5

TECH Addict

iTrader: (21)

Joined: Nov 2005

Posts: 2,209

Likes: 0

From: Maine USA

Quote:

Originally Posted by Nsty98LS1

where are you guys getting the plastic to make these delete panels? i've been trying to find it locally, but with no luck.

Rowmark Laserable Plastic (goggle Rowmark). Most engravers (award places) can get it, not many have the textured style in stock (or 1/8" thick for that matter) as they mostly do awards and are into glossy and flashy. Use 1/8" thick, 1/16" is to flexible when you push switches. The stuff bandsaws well and can be shaped with a file.

It cuts and engraves even better if you have a laser engraver

Jim

Reply Subscribe