Carter01 SBE Nitrous Update.....
Carter01 SBE Nitrous Update..... Well folks I figured I would at least post up a rough pic of where I'm at right now with my build. As many of you know I hit a wall at the 9.50 zone with my SBE 3335lb car. At that point in time I had mainly all stock stuff like injectors, intake, tb, maf etc..
Recently I purchased a set of PRC 225 As-cast heads from Aaron at TSP and a intake combo from John Schaeffer consisting of 42lb injectors, ported Vic Jr intake with Nitro Dave spray bars and a Accufab TB. I am dropping the car off with my NA tuner today for a solid street tune then we will hit the dyno for a power tune. Once that's done i will work the N20 tune out on the track. Currently I have a 82 jet in her awaiting the track debut. Not sure what i am going to do with the old induction system but the guy that tunes also does excellent work with aluminum so i might get him to just make me a plate. Heck i might just leave it as is to get some cold air under the hood. I still have some work to do with wiring and clean-up but she is functional and ready to get tuned!
Recently I purchased a set of PRC 225 As-cast heads from Aaron at TSP and a intake combo from John Schaeffer consisting of 42lb injectors, ported Vic Jr intake with Nitro Dave spray bars and a Accufab TB. I am dropping the car off with my NA tuner today for a solid street tune then we will hit the dyno for a power tune. Once that's done i will work the N20 tune out on the track. Currently I have a 82 jet in her awaiting the track debut. Not sure what i am going to do with the old induction system but the guy that tunes also does excellent work with aluminum so i might get him to just make me a plate. Heck i might just leave it as is to get some cold air under the hood. I still have some work to do with wiring and clean-up but she is functional and ready to get tuned!
Trending Topics
Thanks guys!
@ATV - I have a 2 inch spacer ready to go on hence the long TB studs. However I need a cowl hood to make the 2 in spacer work. Money, Money, Money......
@ATV - I have a 2 inch spacer ready to go on hence the long TB studs. However I need a cowl hood to make the 2 in spacer work. Money, Money, Money......
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Gifts Neither Your Dad Nor Grad Will Shove Into the 'Trinket Drawer'
Brett Foote
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Thanks Ryan, we will be bringing her down real soon to finish the power tune. Gonna street tune it for now to work out the bugs.
Good old tsp trq2 that I've been running for about 5 years. Before with the stock stuff she made 390 rhwp. I will post up both graphs once the dyno tune is complete.
Just as soon as we finish the tune, hit the dyno for a few pulls then we will be at sgmp.
As far as your TH400 goes, well that is great! 9 sec GTO here we come!
Thanks everybody, I have debated on doing this swap for years and finally decided to bite the bullet. I hope to represent well for the SBE LS world!!!
As far as your TH400 goes, well that is great! 9 sec GTO here we come!
Thanks everybody, I have debated on doing this swap for years and finally decided to bite the bullet. I hope to represent well for the SBE LS world!!!
