Running Nitrous Lines

Reply Subscribe

Thread Tools

Search this Thread

Aug 29, 2006 | 04:45 PM

DropTopBird

Thread Starter

TECH Resident

iTrader: (18)

Joined: Jan 2006

Posts: 888

Likes: 0

From: Central PA

Running Nitrous Lines

Hey guys. I have a NOS 5177 dry set up in my car with the bottle on the hump inbetween the back seats. Everything is all set up except for the auctual nitrous lines going from the bottle to the solonoids. My question is, what is the best way to run the lines between the two??? Would it be through the firewall and under the center console? I also heard that there is a hole under the back seats that you can use to run the lines. Im not a big fan of drilling holes in my body but i will if there is no other way. Any help would be greatly appreciated.

Aug 29, 2006 | 05:55 PM

sprydncamd ta

12 Second Club

iTrader: (4)

Joined: Sep 2005

Posts: 538

Likes: 0

From: SPRINGFIELD PA

there is also a hole with a rubber groumet in front of the passenger seat

Aug 29, 2006 | 05:58 PM

ROLLN

On The Tree

Joined: Feb 2006

Posts: 136

Likes: 0

From: ILLINOIS

i would also like to know what the best way is, i am putting my kit in tommorro.

Aug 29, 2006 | 07:12 PM

96prplz28

11 Second Club

iTrader: (14)

Joined: Feb 2004

Posts: 120

Likes: 0

From: St.Peters, MO

I ran mine underneath the carpet and under the center console then up under the dash through the firewall. i perfer not to drill holes on the bottom of my car.

Aug 31, 2006 | 01:38 AM

DropTopBird

Thread Starter

TECH Resident

iTrader: (18)

Joined: Jan 2006

Posts: 888

Likes: 0

From: Central PA

Anyone else have thoughts on how to do this??

Aug 31, 2006 | 08:32 AM

turbo86

On The Tree

iTrader: (4)

Joined: May 2006

Posts: 176

Likes: 0

From: Western KY

There is also a rubber gromlet under the passengers side floor pan, you could run through there, and then up the rail to the engine compartment.....

Aug 31, 2006 | 10:55 AM

n2o

TECH Enthusiast

iTrader: (1)

Joined: Jan 2003

Posts: 702

Likes: 0

From: Saban Country

Those are the two "best" ways that have been mentioned. Rubber grommet and under console through firewall.

7 Most Reliable High-Performance Engines GM Has Ever Built

Verdad Gallardo

Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin

Verdad Gallardo

6 Common C5 Corvette Failures and What's Involved In Repairing Them

Pouria Savadkouei

Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph

Verdad Gallardo

Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked

Pouria Savadkouei

Top 10 Most Powerful Chevy Trucks Ever Made!

Hennessey's New Supercharged Silverado ZR2 Has 700 HP

Verdad Gallardo

Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes

Verdad Gallardo

Awesome K5 Blazer Restomod Comes With C7 Corvette Power

Verdad Gallardo

10 Camaros You Should Never Buy

Sep 1, 2006 | 07:13 PM

Brian2006

TECH Senior Member

iTrader: (42)

Joined: Dec 2004

Posts: 5,063

Likes: 0

From: Tomball/Nacogdoches TX

I have the same kit and I ran mine under the lower door sill (don't know if that's what it's called) and thru the firewall and to the solenoids.

Sep 1, 2006 | 08:24 PM

#10

SSDoubleK

TECH Enthusiast

iTrader: (100)

Joined: Aug 2005

Posts: 635

Likes: 1

From: Greenville PA

Under passenger side sill plate, to the passenger side rubber gromet that is in the firewall behind your glove compartment on the passenger side, no drilling at all. Real easy way to run your line.

Sep 4, 2006 | 10:58 AM

#11

zelich

Teching In

Joined: Feb 2006

Posts: 7

Likes: 0

From: Johnstown, NY

i ran mine out the rubber gromit in the spair tire well, there is a hole in frame right next to it that runs all the way to the engine bay. i also ran my purg line into the same hole in the engine bay so you cann't see the purg spray. VERY CLEAN.