Nitrous Oxide Installation | Tuning | Products
Sponsored by:
Sponsored by:

Need Help this morning (window switch)!

Thread Tools
 
Search this Thread
 
Old 08-05-2007, 09:51 AM
  #1  
12 Second Club
Thread Starter
iTrader: (13)
 
sworaz's Avatar
 
Join Date: Jul 2006
Location: Wisconsin
Posts: 1,142
Likes: 0
Received 0 Likes on 0 Posts

Default Need Help this morning (window switch)!

Have a couple q's for those that know wiring a window switch:
On they dyno tune stage 2 switch there is 6 wires
Orange: not using because i'm not running stage 2
Green: Goes to tach wire #35 on pcm
Yellow: goes to #85 on relay
Blak : Ground
* White says to keyed 12 volt source or arming switch: Is this white wire supposed to be straight to a positive power source? Does it say arming switch in case you wanted to be able to turn it on/off?

* Green is supposed to go to TPS or WOT input wire...I can't seem to find any info as to where this goes???
Old 08-05-2007, 10:25 AM
  #2  
TECH Junkie
iTrader: (17)
 
Tally TransAm's Avatar
 
Join Date: Nov 2001
Location: Tallahassee, Fl
Posts: 3,410
Likes: 0
Received 2 Likes on 2 Posts

Default

you run the white wire to the arming switch so when you turn the switch on to arm the system it turns on the window switch. i would just run it right to power otherwise it will always be on

the tps wire on a 98 should be the dark blue wire coming out of pin 12 on the pcm
Old 08-05-2007, 12:12 PM
  #3  
TECH Resident
iTrader: (9)
 
nickdotcom's Avatar
 
Join Date: Oct 2005
Location: Clear Lake, Texas
Posts: 958
Likes: 0
Received 0 Likes on 0 Posts

Default

you hook it up the your switch so its not on all the time. if you hook it u directly to power it will not only be on all the time, even with the car off, but if you ever feel like getting on it without spraying your solenoids will click anyway. this will spray nothing but fuel, unless your bottle is open, and bog you down pretty good.
Old 08-05-2007, 12:24 PM
  #4  
12 Second Club
Thread Starter
iTrader: (13)
 
sworaz's Avatar
 
Join Date: Jul 2006
Location: Wisconsin
Posts: 1,142
Likes: 0
Received 0 Likes on 0 Posts

Default

Ok on the left side of the TB there is two sensors one lower and one above it...they both have blue wires so which one is it?
Old 08-05-2007, 12:48 PM
  #5  
12 Second Club
Thread Starter
iTrader: (13)
 
sworaz's Avatar
 
Join Date: Jul 2006
Location: Wisconsin
Posts: 1,142
Likes: 0
Received 0 Likes on 0 Posts

Default

Jeesh wtf!
Old 08-05-2007, 01:24 PM
  #6  
TECH Resident
iTrader: (9)
 
nickdotcom's Avatar
 
Join Date: Oct 2005
Location: Clear Lake, Texas
Posts: 958
Likes: 0
Received 0 Likes on 0 Posts

Default

wait more than 24 minutes for a responce.....


in your first post you said your going through the pcm, why did you change to TB?

i couldn't tell ya because i went through the pcm
Old 08-05-2007, 01:31 PM
  #7  
12 Second Club
Thread Starter
iTrader: (13)
 
sworaz's Avatar
 
Join Date: Jul 2006
Location: Wisconsin
Posts: 1,142
Likes: 0
Received 0 Likes on 0 Posts

Default

Originally Posted by nickdotcom
wait more than 24 minutes for a responce.....


in your first post you said your going through the pcm, why did you change to TB?

i couldn't tell ya because i went through the pcm
lol, because that's where the TPS sensor is....thanks for help found it.




All times are GMT -5. The time now is 05:25 AM.