Nitrous Oxide Installation | Tuning | Products
Sponsored by:
Sponsored by:

SES light after NO2 install!?!? help

Thread Tools
 
Search this Thread
 
Old Aug 6, 2007 | 10:11 PM
  #21  
ChaseSS's Avatar
Thread Starter
TECH Fanatic
iTrader: (17)
 
Joined: Jun 2004
Posts: 1,373
Likes: 0
From: St. Louis
Default

Originally Posted by BLK02WS6
No, the plug I'm talking about is down under the car on the trans - did you have that off? There may be a fuse that covers those too - check all your fuses when something like that happens - especially if you didn't mess with any wiring in those areas.

will do... thanks for helping me out through all this, I appreciate it
Reply
Old Aug 7, 2007 | 05:37 PM
  #22  
ChaseSS's Avatar
Thread Starter
TECH Fanatic
iTrader: (17)
 
Joined: Jun 2004
Posts: 1,373
Likes: 0
From: St. Louis
Default

good freaking grief....... I tried tapping the #10 white wire and now the car won't even start, it tries to but won't turn over
Reply
Old Aug 7, 2007 | 07:56 PM
  #23  
BLK02WS6's Avatar
9 Second Club
iTrader: (2)
 
Joined: Jul 2002
Posts: 2,583
Likes: 1
From: on the dyno tuning in MD
Default

Originally Posted by ChaseSS
good freaking grief....... I tried tapping the #10 white wire and now the car won't even start, it tries to but won't turn over
Sounds like something might be up with that window switch! That might be the culprit. Take it off and see if all is back to normal. You sure you are hooking up the window switch right?? You got some gremlins for sure! Little bastards can be a pain sometimes lol!
Reply
Old Aug 7, 2007 | 08:11 PM
  #24  
ChaseSS's Avatar
Thread Starter
TECH Fanatic
iTrader: (17)
 
Joined: Jun 2004
Posts: 1,373
Likes: 0
From: St. Louis
Default

Originally Posted by BLK02WS6
Sounds like something might be up with that window switch! That might be the culprit. Take it off and see if all is back to normal. You sure you are hooking up the window switch right?? You got some gremlins for sure! Little bastards can be a pain sometimes lol!

I know, its driving me crazy... I just went through all the connections on the window switch and the TPS switch and everything seems right, checked all the fuses and they were fine too. I don't understand this

How hard is it to short out the PCM? Is it possible that its the problem? (although all my engine lights and everything come on when I turn the key, it just won't start which makes me think that the PCM is not the problem... but I will go try taking off the window switch and see if that does it
Reply
Old Aug 7, 2007 | 08:38 PM
  #25  
ChaseSS's Avatar
Thread Starter
TECH Fanatic
iTrader: (17)
 
Joined: Jun 2004
Posts: 1,373
Likes: 0
From: St. Louis
Default

just checked the window switch.... its not the problem... the problem is I am going to commit suicide over this damn install. Tomorrow I am getting my volt meter back from a friend who borrowed it and I will have to check the big metal fuses that I couldn't today
Reply
Old Aug 7, 2007 | 08:42 PM
  #26  
BLK02WS6's Avatar
9 Second Club
iTrader: (2)
 
Joined: Jul 2002
Posts: 2,583
Likes: 1
From: on the dyno tuning in MD
Default

Aww don't do that lol! You sure it isn't just the battery down after all this ordeal? Is it clicking and trying to engage the starter, but just not turning over? Or is the starter cranking the engine over?
Reply
Old Aug 7, 2007 | 10:01 PM
  #27  
ChaseSS's Avatar
Thread Starter
TECH Fanatic
iTrader: (17)
 
Joined: Jun 2004
Posts: 1,373
Likes: 0
From: St. Louis
Default

its clinking and trying to start the car, not the battery (just replaced it 2 months ago) but I will look at the starter fuse tomorrow... it has to be a fuse (it f#$%ing better be a fuse), nothing else makes sense in this crazy world of nitrous wiring
Reply




All times are GMT -5. The time now is 12:24 AM.