GN Parts, 82-92 Fbody Swap parts!!
#1
12 Second Club
Thread Starter
iTrader: (11)
Join Date: Aug 2005
Location: Ohio
Posts: 836
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Engine (was rebuilt 3/07 but has spun bearings disassembled 10/08)
3.8L 109 Block bored .030
Stock turbo crank .020/.020
Stock Turbo Rods
TRW/Speed Pro Forged pistons (.030)
Stock Main caps w/ ARP Studs
Stock Un-ported 8445 heads w/ 100lb springs (rebuilt and resurfaced 3/07)
Stock Rocker shafts and arms
Stock front cover w/ rebuilt oil pump (had 40psi cold and 18-20psi hot idle oil psi)
$800 obo Will not ship engine!!
Accessory Drive
Alternator-$50
Main accessory bracket-$50
AC Delete Pulley-$30
Power Steering Pump and pulley-$50
Water pump and pulley-$35
Tensioner and idler pulley-$20
Turbo Balancer and pulley-$100
Intercooler fan-$40
Serpentine Belt-$5
Hot side parts
Stock Manifolds and crossover (resurfaced and cracks repaired 8/08)-$100
Turbonetics TE-44 .63 AR, doesnt smoke but should rebuild due to too much shaft play(up and down)-$200
3 Custom Downpipe w/ HKS wastegate w/ 20psi spring. Comes with 3 Custom Cat. Will bolt up to Single cat Fbody exhaust systems(PM for more info) WILL NOT FIT TTAs, only Buick headed 3rd gen applications!!-$350
GN Test Pipe-$30
Cold Side parts
Stock Intercooler w/ Duttweiller neck modification (comes with hoses)- $125
3 Chrome MAF Pipe w/hoses (shortened a buick one to work in Third Gen)-$50
2.5 Chrome Up Pipe (drilled for single nozzle AlkyControl Kit)-$25
Stock Un-ported Lower intake manifold-$50
Kenne Bell 70mm upper plenum and throttle body combo (comes w/ hose and sensors)-$400
RJC powerplate for KB and Accufab Plenums-$50
Electronics
Stock 86/87 MAF-50
Cam Sensor-$60
Ignition Control Module and Coil pack (both bought 9/08 from AutoZone)-$100
Kirban Spark Plug Wires-$40
55# Siemens Low Impedance Injectors-$200
Modified Low Impedance ECM (Done by quad Air)-$150
TurboTweak 93 Street Chip and Alky Chips by Eric Marshall-$90
Crank Sensor (bought 8/07 from NAPA)-$40
Injector harness-$25
Misc Parts
Engine Mounts-$30
TTA Frame Pads-$50
Stock Fuel Rail w/ bosch adjustable Fuel Pressure Regulator-$50
Kenne Bell Hood Mount FP Gauge (Missing Hood Mount)-$50
TTA Radiator Hoses-$20
Vacuum Block and hoses-$50
Heater Core Lines-$20
![](http://img252.imageshack.us/img252/3137/sany0338lo0.jpg)
![](http://img519.imageshack.us/img519/1299/sany0340to5.jpg)
![](http://img519.imageshack.us/img519/871/sany0346xr7.jpg)
![](http://img252.imageshack.us/img252/2438/sany0343xm2.jpg)
![](http://img266.imageshack.us/img266/5180/sany0351et2.jpg)
![](http://img252.imageshack.us/img252/2903/sany0341cz5.jpg)
3.8L 109 Block bored .030
Stock turbo crank .020/.020
Stock Turbo Rods
TRW/Speed Pro Forged pistons (.030)
Stock Main caps w/ ARP Studs
Stock Un-ported 8445 heads w/ 100lb springs (rebuilt and resurfaced 3/07)
Stock Rocker shafts and arms
Stock front cover w/ rebuilt oil pump (had 40psi cold and 18-20psi hot idle oil psi)
$800 obo Will not ship engine!!
Accessory Drive
Alternator-$50
Main accessory bracket-$50
AC Delete Pulley-$30
Power Steering Pump and pulley-$50
Water pump and pulley-$35
Tensioner and idler pulley-$20
Turbo Balancer and pulley-$100
Intercooler fan-$40
Serpentine Belt-$5
Hot side parts
Stock Manifolds and crossover (resurfaced and cracks repaired 8/08)-$100
Turbonetics TE-44 .63 AR, doesnt smoke but should rebuild due to too much shaft play(up and down)-$200
3 Custom Downpipe w/ HKS wastegate w/ 20psi spring. Comes with 3 Custom Cat. Will bolt up to Single cat Fbody exhaust systems(PM for more info) WILL NOT FIT TTAs, only Buick headed 3rd gen applications!!-$350
GN Test Pipe-$30
Cold Side parts
Stock Intercooler w/ Duttweiller neck modification (comes with hoses)- $125
3 Chrome MAF Pipe w/hoses (shortened a buick one to work in Third Gen)-$50
2.5 Chrome Up Pipe (drilled for single nozzle AlkyControl Kit)-$25
Stock Un-ported Lower intake manifold-$50
Kenne Bell 70mm upper plenum and throttle body combo (comes w/ hose and sensors)-$400
RJC powerplate for KB and Accufab Plenums-$50
Electronics
Stock 86/87 MAF-50
Cam Sensor-$60
Ignition Control Module and Coil pack (both bought 9/08 from AutoZone)-$100
Kirban Spark Plug Wires-$40
55# Siemens Low Impedance Injectors-$200
Modified Low Impedance ECM (Done by quad Air)-$150
TurboTweak 93 Street Chip and Alky Chips by Eric Marshall-$90
Crank Sensor (bought 8/07 from NAPA)-$40
Injector harness-$25
Misc Parts
Engine Mounts-$30
TTA Frame Pads-$50
Stock Fuel Rail w/ bosch adjustable Fuel Pressure Regulator-$50
Kenne Bell Hood Mount FP Gauge (Missing Hood Mount)-$50
TTA Radiator Hoses-$20
Vacuum Block and hoses-$50
Heater Core Lines-$20
![](http://img252.imageshack.us/img252/3137/sany0338lo0.jpg)
![](http://img519.imageshack.us/img519/1299/sany0340to5.jpg)
![](http://img519.imageshack.us/img519/871/sany0346xr7.jpg)
![](http://img252.imageshack.us/img252/2438/sany0343xm2.jpg)
![](http://img266.imageshack.us/img266/5180/sany0351et2.jpg)
![](http://img252.imageshack.us/img252/2903/sany0341cz5.jpg)
![](http://img252.imageshack.us/img252/sany0341cz5.jpg/1/w640.png)