P4s
11-23-2008, 09:30 AM
#1
TECH Regular
Thread Starter
iTrader: (2)
Join Date: May 2004
Location: Kitchener, Ontario
Posts: 406
Likes: 0
Received 0 Likes
on
0 Posts
P4s Hey Guys,
Well i am selling off everything, i have all the right parts here to make a 600-1000hp car all hi-end parts SO PLEASE NO LOW BALLERS
This is off my 95 T/A
I HAVE PICS OF EVERYTHING I WILL POST OR I CAN EMAIL THEM
Vortech cog pulleys 36mm, 78 teeth crank/30 blower
2 X custom 4" piping for vortech blower suck side and air filter
vortech mondo BOV
Alky control kit
singal kit & new dual kit as well, with an new extra pump $440
Nitrous Outlet elbow for Vic intake i will through this in with the heads and intake
Vic Jr intake with fuel rails its fully ported and matched to the heads this stuff is a one off
matching AFR 220 heads
These are Z8's old AFR heads(220) that were ported by GTP that flow 330cfm@.600 and mating Vic intake you will not find another set of heads like this with shaft mounts 1.7r $3000.00
Qa1 for the front (newish) with 250lbs springs and shims $275
sphoon TQ arm $375
short block 355.....blower/nos set up
eagle rods 4340
eagle 4340
Je blower pistions
4 bolt main
balanced
ATi extra keyed crank
e-water
custom Bret B blower cam
Morrel's lifters
MAKE OFFERS ON ENG OR I CAN PART OUT
weld wheels
15x10.5 with 7.5 bs and hoosher slicks $600
NEW MSD DIG 6 NEW 275.00
IF DOING PAYPAL ADD 3%
obo
Well i am selling off everything, i have all the right parts here to make a 600-1000hp car all hi-end parts SO PLEASE NO LOW BALLERS
This is off my 95 T/A
I HAVE PICS OF EVERYTHING I WILL POST OR I CAN EMAIL THEM
Vortech cog pulleys 36mm, 78 teeth crank/30 blower
2 X custom 4" piping for vortech blower suck side and air filter
vortech mondo BOV
Alky control kit
singal kit & new dual kit as well, with an new extra pump $440
Nitrous Outlet elbow for Vic intake i will through this in with the heads and intake
Vic Jr intake with fuel rails its fully ported and matched to the heads this stuff is a one off
matching AFR 220 heads
These are Z8's old AFR heads(220) that were ported by GTP that flow 330cfm@.600 and mating Vic intake you will not find another set of heads like this with shaft mounts 1.7r $3000.00
Qa1 for the front (newish) with 250lbs springs and shims $275
sphoon TQ arm $375
short block 355.....blower/nos set up
eagle rods 4340
eagle 4340
Je blower pistions
4 bolt main
balanced
ATi extra keyed crank
e-water
custom Bret B blower cam
Morrel's lifters
MAKE OFFERS ON ENG OR I CAN PART OUT
weld wheels
15x10.5 with 7.5 bs and hoosher slicks $600
NEW MSD DIG 6 NEW 275.00
IF DOING PAYPAL ADD 3%
obo
11-23-2008, 04:10 PM
#2
Launching!
iTrader: (15)
Join Date: Jan 2008
Location: 81 NY support
Posts: 214
Likes: 0
Received 0 Likes
on
0 Posts
will the qa1's work on an LS1 car ? if so I would take them if you can send a pic to me 8secondz@gmail.com
