Built 4l60E and 3600 Stall
02-24-2009, 09:37 PM
#22
TECH Enthusiast
iTrader: (7)
Join Date: Jul 2006
Location: College Station,TX/Indy,IN
Posts: 600
Likes: 0
Received 0 Likes
on
0 Posts
well the list is kinda long but
first off an old cargo van
then car parts
Swracecars 10pt cage kit
lt1 tubular kmember.. Rear drag way bar. new 28x10.5 et drags..GOOD chassis mount torque arm.. Beefy th350 stall. Decent set of racing seats for fat people .. Ultrabell for th350.. Manual brake conversion..
BUt uhh what do you have?
first off an old cargo van
then car parts
Swracecars 10pt cage kit
lt1 tubular kmember.. Rear drag way bar. new 28x10.5 et drags..GOOD chassis mount torque arm.. Beefy th350 stall. Decent set of racing seats for fat people .. Ultrabell for th350.. Manual brake conversion..
BUt uhh what do you have?
I have a 1992 Ford E250 cargo van!!!!!! and i have racing seats!!!
PM ME PM ME!!!
04-27-2009, 03:10 PM
#30
Staging Lane
Thread Starter
iTrader: (4)
Join Date: Aug 2006
Posts: 55
Likes: 0
Received 0 Likes
on
0 Posts
I have some of the receipts not sure on all of them
i am a wee bit unorganized when it comes to paper work
as for shipping i am willing to ship it BUT i would very much rather have it picked up
i am willing to drive to meet within reason (50 OR 60 MILES)
i am a wee bit unorganized when it comes to paper work
as for shipping i am willing to ship it BUT i would very much rather have it picked up
i am willing to drive to meet within reason (50 OR 60 MILES)
04-29-2009, 04:45 PM
#35
Staging Lane
Thread Starter
iTrader: (4)
Join Date: Aug 2006
Posts: 55
Likes: 0
Received 0 Likes
on
0 Posts
id say probably 500 -550 safely
but in my opinion HP ratings are a semi arbitrary number
If you are running a fully built high compression heads cam ++++ motor and sprayin 300 on it this might not be the tranny for you
but you never know it might hold it
If you have a pump gas built street motor heads cam and mild 11:1 compression all motor or a bolt on cam only car on a decent 150 shot this is gonna be just fine for you
but in my opinion HP ratings are a semi arbitrary number
If you are running a fully built high compression heads cam ++++ motor and sprayin 300 on it this might not be the tranny for you
but you never know it might hold it
If you have a pump gas built street motor heads cam and mild 11:1 compression all motor or a bolt on cam only car on a decent 150 shot this is gonna be just fine for you
05-01-2009, 09:38 AM
#38
Staging Lane
Thread Starter
iTrader: (4)
Join Date: Aug 2006
Posts: 55
Likes: 0
Received 0 Likes
on
0 Posts
but it would be questionable on spray
it might hold fine but IMO that is really pushing a 4l60e especially if its full weight
but i can be over cautious when it comes to this stuff
05-01-2009, 01:42 PM
#39
TECH Enthusiast
iTrader: (12)
Join Date: Aug 2006
Location: Texas
Posts: 533
Likes: 0
Received 0 Likes
on
0 Posts
so your cautious about 450+ hp. Damn my goal is higher than that. I hope to make near 550-600 hp. on my turbo setup. I guess it is time to start looking for a th400 th350 setup.
