SBC's, BBC's, SB2, complete and parts, cylinder heads!!!!
02-18-2009, 07:43 AM
#1
SBC's, BBC's, SB2, complete and parts, cylinder heads!!!! Looking to get arid of a lot of stuff and for good prices too!
AFR 220cc 23 degree cylinder heads full race port job.
75cc chambers Rev stainless valves 2.125x5.060, 1.625x5.060
Isky springs 250lbs on the seat. Del West ti retainers.
Comes with Crower shaft mount rocker system set up for these heads, 1.5,1.5.
With or without maching HVH Brodix intake manifold. $2000.00 w/o intake no reasonable offers refused.
SB2 long block.
4.185 bore. Chevy Bowtie 4 bolt splayed cap block. Roller cam bearings, Clevitte main and rod bearings, Bryant 3.270"crankshaft-std mains/.010 rods, Dyers 6.250" rods with Honda pins, JE pistons and ring set, SB2 fully ported heads; 45.2cc, Xceldyne titanium intake and exhaust valves, Jesel rocker arms, Baker designed roller camshaft with matching lifters, high tech one piece push rods, Jesel belt drive system, Fel- Pro performance gaskets, Pro/Cam aluminum dry sump oil pan, valve covers with oilers, MSD distributor, aluminum water pump, Pro/Cam fuel pump and Champion spark plugs. Dyno tested and tuned FRESH and ready to race! Only 16,500.00!!!
454/350hp long block. GM 4-bolt Gen V block +.030". Clevitte 77 bearings, Speed Pro hyperutectic pistons, 9:1 compression, Speed-Pro ring set, Gm forged 4.000" crank; std/std, GM rectangular port 118cc cylinder heads with Ferrea stainless steel intake and exhaust valves, Baker designed hyd. camshaft with matching lifters, aluminum dual plane intake manifold, Fel-Pro performance gaskets. Balanced and blueprinted. Only 2,900.00!!!
Many other parts, cranks rods, blocks, heads, intakes....
AFR 220cc 23 degree cylinder heads full race port job.
75cc chambers Rev stainless valves 2.125x5.060, 1.625x5.060
Isky springs 250lbs on the seat. Del West ti retainers.
Comes with Crower shaft mount rocker system set up for these heads, 1.5,1.5.
With or without maching HVH Brodix intake manifold. $2000.00 w/o intake no reasonable offers refused.
SB2 long block.
4.185 bore. Chevy Bowtie 4 bolt splayed cap block. Roller cam bearings, Clevitte main and rod bearings, Bryant 3.270"crankshaft-std mains/.010 rods, Dyers 6.250" rods with Honda pins, JE pistons and ring set, SB2 fully ported heads; 45.2cc, Xceldyne titanium intake and exhaust valves, Jesel rocker arms, Baker designed roller camshaft with matching lifters, high tech one piece push rods, Jesel belt drive system, Fel- Pro performance gaskets, Pro/Cam aluminum dry sump oil pan, valve covers with oilers, MSD distributor, aluminum water pump, Pro/Cam fuel pump and Champion spark plugs. Dyno tested and tuned FRESH and ready to race! Only 16,500.00!!!
454/350hp long block. GM 4-bolt Gen V block +.030". Clevitte 77 bearings, Speed Pro hyperutectic pistons, 9:1 compression, Speed-Pro ring set, Gm forged 4.000" crank; std/std, GM rectangular port 118cc cylinder heads with Ferrea stainless steel intake and exhaust valves, Baker designed hyd. camshaft with matching lifters, aluminum dual plane intake manifold, Fel-Pro performance gaskets. Balanced and blueprinted. Only 2,900.00!!!
Many other parts, cranks rods, blocks, heads, intakes....
03-02-2009, 07:23 AM
#4
Another set of 18 degree #363's trade ins all freshened up ready to run. Come with #10185053 Gm matching intake and Jesel KPS 10509 shaft rocker system. Worked by Katech, only looking for $2800.00 for all of it!!!!!! Over 6k in goodies here.
