Mufflex, Direct Port Manifold, 9" Housing TB and LOTS of GO FAST LT1 PARTS
#24
12 Second Club
Thread Starter
iTrader: (35)
Join Date: Jan 2006
Location: Danville PA
Posts: 1,550
Likes: 0
Received 0 Likes
on
0 Posts
I replied to your PM. But ill just post up details about the trans. Its a CPT (Cahall Performance Transmissions) Pro Race 4L60E. This trans is behind many 9 second cars and will handle whatever you can throw at it. There are 1200 miles on this trans 500 of them being break-in miles. It shifts HARD and will def. perform like no other. I do however need a good working STOCK trans in order to sell this one. The stock trans must be in good working condition with realatively low miles. Im not about to put a junk trans in the car and screw the potential buyer of the car.
Harold
Harold
#26
Staging Lane
iTrader: (12)
Join Date: Nov 2007
Location: Catasauqua Pa.
Posts: 57
Likes: 0
Received 0 Likes
on
0 Posts
I sent you a pm on the exhaust. I had a vig conveter in a GN and a 9 second IROC and had them both break under 500 miles, and went through 2 Yanks in a Impala SS for no reason. Screw the names, as long as it is holding together it is gold by me. Everything made today doesn't last! Bump for some nice parts
#27
12 Second Club
Thread Starter
iTrader: (35)
Join Date: Jan 2006
Location: Danville PA
Posts: 1,550
Likes: 0
Received 0 Likes
on
0 Posts
I sent you a pm on the exhaust. I had a vig conveter in a GN and a 9 second IROC and had them both break under 500 miles, and went through 2 Yanks in a Impala SS for no reason. Screw the names, as long as it is holding together it is gold by me. Everything made today doesn't last! Bump for some nice parts
#35
12 Second Club
Thread Starter
iTrader: (35)
Join Date: Jan 2006
Location: Danville PA
Posts: 1,550
Likes: 0
Received 0 Likes
on
0 Posts
300.00 for the Headers.
90.00 for the Y-Pipe.
They have AIR and EGR fittings. They also have the typical rust and ceramic coating peel near the collectors.
The block comes with the crank, rods, and pistons. Come pick it up for 100 bucks. Or make arrangements for shipping.
Harold
90.00 for the Y-Pipe.
They have AIR and EGR fittings. They also have the typical rust and ceramic coating peel near the collectors.
The block comes with the crank, rods, and pistons. Come pick it up for 100 bucks. Or make arrangements for shipping.
Harold
#36
On The Tree
Join Date: Apr 2008
Location: Mcleansville NC
Posts: 142
Likes: 0
Received 0 Likes
on
0 Posts
Have u got any pics of the block??? And how far away are you from Carisle, Penn.??? Im headed there in a month for GM nationals and would like to find a way to look at your block.
#37
12 Second Club
Thread Starter
iTrader: (35)
Join Date: Jan 2006
Location: Danville PA
Posts: 1,550
Likes: 0
Received 0 Likes
on
0 Posts
Harold
#38
On The Tree
Join Date: Apr 2008
Location: Mcleansville NC
Posts: 142
Likes: 0
Received 0 Likes
on
0 Posts
yea im trying to buy a block because i got a 383 on my mind... And im headed to the Gm nationals in a few weeks. Ill take a look at the pics... sorry my dad is one of those whole gotta see it in person so im unsure of purchase. Jordan
#39
12 Second Club
Thread Starter
iTrader: (35)
Join Date: Jan 2006
Location: Danville PA
Posts: 1,550
Likes: 0
Received 0 Likes
on
0 Posts
You can look at my trader feedback I never screw anyone over. Im straight up and honest with everything I sell. You can come look at it if you would like. All your going to see is a block, crank, piston, caps, and rods. I was going to use it for a 396 build, but have since decided to sell everything. Let me know what you decide to do.
Harold
Harold