Complete 383 LT1
07-18-2008, 12:55 AM
#1
Launching!
Thread Starter
iTrader: (9)
Join Date: May 2006
Location: Paragould AR
Posts: 212
Likes: 0
Received 0 Likes
on
0 Posts
Complete 383 LT1 Decided to go another route with my set up so Im selling my engine complete ready to run
Factory Block decked, line honed, no hard fill, 4 bolt splayed billet main conversion, bored .030.
Eagle rotating assembly 6" rods 3.75 stroke
ARP everything
12.5:1 compression
Custom grind solid roller(245/253@.050 640 lift 112lsa)
Comp double roller timing chain
Fully ported stock heads, relocated pushrods to eliminate pinch 56cc chambers, race valve job 2.02/1.60 valves comp springs titanium retainers
T&D shaft mounts 1.6 ratio, intake offset .150 to accomodate heads
Custom sheet metal valve covers
GZ Motorsports complete vacuum pump kit
Holley Stealth Ram intake fully ported lower, upper ported for monoblade
ASM monoblade
Racetronix 42# injectors
New ac delco optispark
B&M SFI flywheel
Professional Products SFI balancer
Madman alt relocation bracket
Canton oil pan
Braided steam line conversion
Also Including a dell laptop with tunercats, datamaster, freescan
PCM with Ed Wright dyno tune
Car has been 11.01@120 N/A at 34xx pounds on 93 octane pump gas thru a th400 and a 3800 convertor and a 12 bolt. It is currently in the car running, will pull out as soon as it is time in case anybody want to hear it run. There is 5 or 6 passes on it since freshening.
Pics:
http://i200.photobucket.com/albums/a...8/DSC00469.jpg
http://i200.photobucket.com/albums/a...8/DVC00311.jpg
http://i200.photobucket.com/albums/a...8/DVC00291.jpg
Video of 11.01 pass
http://www.youtube.com/watch?v=oWyJjTrdzag
Asking $6500obo for everything. I will ship at buyers expense or deliver/meet up to 400 miles. Located in Paragould Arkansas. Thanks for looking.
Factory Block decked, line honed, no hard fill, 4 bolt splayed billet main conversion, bored .030.
Eagle rotating assembly 6" rods 3.75 stroke
ARP everything
12.5:1 compression
Custom grind solid roller(245/253@.050 640 lift 112lsa)
Comp double roller timing chain
Fully ported stock heads, relocated pushrods to eliminate pinch 56cc chambers, race valve job 2.02/1.60 valves comp springs titanium retainers
T&D shaft mounts 1.6 ratio, intake offset .150 to accomodate heads
Custom sheet metal valve covers
GZ Motorsports complete vacuum pump kit
Holley Stealth Ram intake fully ported lower, upper ported for monoblade
ASM monoblade
Racetronix 42# injectors
New ac delco optispark
B&M SFI flywheel
Professional Products SFI balancer
Madman alt relocation bracket
Canton oil pan
Braided steam line conversion
Also Including a dell laptop with tunercats, datamaster, freescan
PCM with Ed Wright dyno tune
Car has been 11.01@120 N/A at 34xx pounds on 93 octane pump gas thru a th400 and a 3800 convertor and a 12 bolt. It is currently in the car running, will pull out as soon as it is time in case anybody want to hear it run. There is 5 or 6 passes on it since freshening.
Pics:
http://i200.photobucket.com/albums/a...8/DSC00469.jpg
http://i200.photobucket.com/albums/a...8/DVC00311.jpg
http://i200.photobucket.com/albums/a...8/DVC00291.jpg
Video of 11.01 pass
http://www.youtube.com/watch?v=oWyJjTrdzag
Asking $6500obo for everything. I will ship at buyers expense or deliver/meet up to 400 miles. Located in Paragould Arkansas. Thanks for looking.
Last edited by Tapout911; 07-18-2008 at 11:22 AM.
