Parting out 12 sec TPI-T56 Combo
#1
Teching In
Thread Starter
iTrader: (1)
Join Date: Jan 2008
Posts: 26
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Descreened MAF
Airfoil
TPIS 58mm TB
K&N Air Filters
24 lb/hr Fuel injectors
TPIS Bigmouth Intake Manifold
SLP High flow intake runners
3rd gen Edelbrock TES ceramic coated headers w/air & Ypipe
4th Gen Borla Adj. 3” Catback exhaust (stainless steel)
T-56 Tranny swap from 94 Camaro SS
Aluminum Slave cyl.
Mcleod Clutch Disc
LT1 11” Pressure plate
Yukon 3.73 Ratio Rear End Gears
Steel Driveshaft
Centerforce 2 piece RMS Flywheel for t56 conversion.
Spohn crossmember for t56 conversion
Hurst Sidewinder shift ****
Ws6store short stick
(prefer engine to sell as complete setup)
Has gone 12.87 @ 106 with TPI setup @ 3600 lbs
Hypereutectic Flat-top pistons
Corvette L98 Hyd. Roller Cam
Trick Flow Twisted Wedge Aluminum Heads(1.5 Int. 1.94 exh.)
Crowler 1.6 Roller Rockerarms
Roller lifters
Stock cast crank (350)
4 bolt main – 2 piece rms bored .040 over. Block
Brand new A/c Compressor
Fixed tachometer for 3rd gen camaro (145mph gauges) everything works.
q-power 4x6 front speakers. (brand new and kinda hard to find the size)
6x9 pioneer speakers (model will be posted if interest is shown or when pulled out)
Power drivers seat (torn in 1 section) – IROC seat - gray
Passenger IROC seat – mint – gray
Passenger seats & fold down backing – gray – mint
Recently replaced rear hatch pull down.
Grant steering wheel.
Hypertech chip for 89 camaro 350 automatic
This is a daily driven car that I am parting out so please ask for small things that are not listed.
Email will reach me fastest – Lozercoward@hotmail.com
I will check the forums periodically to update items accordingly
Airfoil
TPIS 58mm TB
K&N Air Filters
24 lb/hr Fuel injectors
TPIS Bigmouth Intake Manifold
SLP High flow intake runners
3rd gen Edelbrock TES ceramic coated headers w/air & Ypipe
4th Gen Borla Adj. 3” Catback exhaust (stainless steel)
T-56 Tranny swap from 94 Camaro SS
Aluminum Slave cyl.
Mcleod Clutch Disc
LT1 11” Pressure plate
Yukon 3.73 Ratio Rear End Gears
Steel Driveshaft
Centerforce 2 piece RMS Flywheel for t56 conversion.
Spohn crossmember for t56 conversion
Hurst Sidewinder shift ****
Ws6store short stick
(prefer engine to sell as complete setup)
Has gone 12.87 @ 106 with TPI setup @ 3600 lbs
Hypereutectic Flat-top pistons
Corvette L98 Hyd. Roller Cam
Trick Flow Twisted Wedge Aluminum Heads(1.5 Int. 1.94 exh.)
Crowler 1.6 Roller Rockerarms
Roller lifters
Stock cast crank (350)
4 bolt main – 2 piece rms bored .040 over. Block
Brand new A/c Compressor
Fixed tachometer for 3rd gen camaro (145mph gauges) everything works.
q-power 4x6 front speakers. (brand new and kinda hard to find the size)
6x9 pioneer speakers (model will be posted if interest is shown or when pulled out)
Power drivers seat (torn in 1 section) – IROC seat - gray
Passenger IROC seat – mint – gray
Passenger seats & fold down backing – gray – mint
Recently replaced rear hatch pull down.
Grant steering wheel.
Hypertech chip for 89 camaro 350 automatic
This is a daily driven car that I am parting out so please ask for small things that are not listed.
Email will reach me fastest – Lozercoward@hotmail.com
I will check the forums periodically to update items accordingly