Steve - when is a good time?
Thread Starter
10 Second Club
iTrader: (4)
Joined: Feb 2004
Posts: 9,448
Likes: 0
From: Marysville, WA
Steve - when is a good time? I was wondering when a good time would be to come over to take a look at your PCM port. We need to get that diagnosed so we can tune your car. Do you work this week? If you had a couple hours to burn maybe we could get your water pump & radiator in too. Lemme know. I'm working today, & may work 1 more day this week.
12 Second Club
Joined: Apr 2004
Posts: 1,647
Likes: 0
From: Redmond Washington
Mark,
I am off Friday, Saturday & Sunday and could cut out early Wednesday or Thursday. Only plans I have for the weekend is I was going to try and rub on that vette out at Ellis's place. When you come over bring your voltage meter & battery charger so we can make sure the battery is properly charged.
I'm still waiting for the brown truck to deliver the T.B., MAF sensor & air lid.
I am off Friday, Saturday & Sunday and could cut out early Wednesday or Thursday. Only plans I have for the weekend is I was going to try and rub on that vette out at Ellis's place. When you come over bring your voltage meter & battery charger so we can make sure the battery is properly charged.
I'm still waiting for the brown truck to deliver the T.B., MAF sensor & air lid.
Thread Starter
10 Second Club
iTrader: (4)
Joined: Feb 2004
Posts: 9,448
Likes: 0
From: Marysville, WA
Looks like we should think about Thur afternoon or Friday. When did you plan to go work on the Vette? I could maybe go Sat for a bit. Any word from Jantzer on your parts?
12 Second Club
Joined: Apr 2004
Posts: 1,647
Likes: 0
From: Redmond Washington
On the Vette I need to check with Ellis. We had talked about Friday a couple of weeks ago. I'll page him after this post.
Last I checked with Jantzer was on the 20th and he said he was almost done.
I talked to the guy doing my lid & FRC about the same time and he was almost done, so like any day now the brown truck should show up.
If we can work trouble shoot the PCM & Finish up with what we got I all for it kinda getting excited about firing her up again.
Last I checked with Jantzer was on the 20th and he said he was almost done.
I talked to the guy doing my lid & FRC about the same time and he was almost done, so like any day now the brown truck should show up.
If we can work trouble shoot the PCM & Finish up with what we got I all for it kinda getting excited about firing her up again.
Thread Starter
10 Second Club
iTrader: (4)
Joined: Feb 2004
Posts: 9,448
Likes: 0
From: Marysville, WA
Well buddy, what's the schedule lookin like? I can pop over Friday for a couple hours. We should be able to get her back together & fired up in that span. Maybe another hour to troubleshoot the PCM.....what say you?
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo