427 SBC DART PROTOPLINE 14 Degree Engine
05-12-2011, 04:19 PM
#1
TECH Enthusiast
Thread Starter
iTrader: (3)
Join Date: Oct 2007
Posts: 629
Likes: 0
Received 0 Likes
on
0 Posts
427 SBC DART PROTOPLINE 14 Degree Engine Category: Engine - Complete Motors
Price: $11500
Part Fits: 67-92 Pontiac Firebird
Location (State): ID
Item Condition: Brand New
Shipping Information: Item Can be Shipped
Engine: Small Block
LS Engine?: Non-LS Part
It is a Dart Little M Pro Series Block that has a standard 4.125" bore (can be taken to 4.200").
Brand new forged Eagle Crank, 4" stroke
Brand new forged Eagle H bead rods with special L19 ARP hi-test rod bolts (added $100 when purchased)
Custom Diamond flat top 14 degree pistons (have two spares, a left and right), 14:1 compression
All was balanced within .25 grams.
SFI fywheel and Rattler harmonic balancer
Has Custom Comp Cam, .700 lift. I have the box and cam card.
Full roller with new monster push rods from Comp that are ment to handle the lift.
Jesel Belt drive, spare belt and carbon fiber cover
The heads are Pro Action/Pro Topline 14 degree race heads.
These are the Kiwi heads that pro stock guys love!
They are fresh, all titanium everything.
T&D Offset shaft mounted rockers
I bought these heads for $6k with spare parts and the rockers
These are the heads that make true power.
Also, I have the intake for a 4500 carb, it has a valley pan and then phenolic spacers that bolts to the heads.
Paid $1K just for the intake! Cant find this intake anymore, very rare.
ARP bolts or studs for everything
Fabricated kicked out all aluminum pan from Moroso.
Has a crank trigger kit on it too with MSD everything
The motor is complete, sitting in my race car that I will never finish.
I was thinking of putting the engine in a drag boat but I just have too many projects.
This is a twin build of a sister engine that Top Gun Terry built. Should put down 850+ hp at the crank
After machining and all of the nuts and bolts, I have over $20K
05-18-2011, 10:06 AM
#4
TECH Enthusiast
Thread Starter
iTrader: (3)
Join Date: Oct 2007
Posts: 629
Likes: 0
Received 0 Likes
on
0 Posts
I would sell the short block for $5500.
That basically covers the cost of the block, pistons and crank.
I am willing to tear the motor down and show that it is all brand new.
Also, there are two spare pistons that go with the engine as well.
That basically covers the cost of the block, pistons and crank.
I am willing to tear the motor down and show that it is all brand new.
Also, there are two spare pistons that go with the engine as well.
05-18-2011, 10:09 AM
#5
TECH Enthusiast
Thread Starter
iTrader: (3)
Join Date: Oct 2007
Posts: 629
Likes: 0
Received 0 Likes
on
0 Posts
Here is the short block costs; All the pars are brand new:
Block Dart Little M $2,300.00
Crank Eagle $650.00
Rods Eagle $500.00
Pistons Diamond $1,600.00
Cam Comp $250.00
Lifters Comp $200.00
Flywheel CSI $125.00
Bearings Clevite Pro $85.00
Balancer TCI Rattler $300.00
Timing Tab Billet $35.00
Bore Block Bob's $200.00
Balance Rotat. Assem. $200.00
ARP Bolt Upgrade $100
$6,545
Will sell for $5500.
Rings were extra too. They have a Napier second ring.
They were all fill fit to the block.
Block Dart Little M $2,300.00
Crank Eagle $650.00
Rods Eagle $500.00
Pistons Diamond $1,600.00
Cam Comp $250.00
Lifters Comp $200.00
Flywheel CSI $125.00
Bearings Clevite Pro $85.00
Balancer TCI Rattler $300.00
Timing Tab Billet $35.00
Bore Block Bob's $200.00
Balance Rotat. Assem. $200.00
ARP Bolt Upgrade $100
$6,545
Will sell for $5500.
Rings were extra too. They have a Napier second ring.
They were all fill fit to the block.
