Brand New Ported All-Pro Cathedral Port Heads Assembled **$2200 Shipped**
#1
Launching!
Thread Starter
iTrader: (17)
Join Date: Jun 2006
Location: Tulsa, Ok
Posts: 251
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Category: Racing Parts
Price: $2200
Location (State): OK
Item Condition: Brand New
Shipping Information: Item Can be Shipped
LS Engine?: Fits LS Engine
Price $2200 Firm...Complete and ready to go.
An equivalent head setup from Mast or to replicate this setup from All-Pro would run anywhere between $3700-$4000.
Payment option: Paypal (to keep me as the seller and the buyer protected this is my preferred payment method, I also have a paypal debit card and I'm a verified member)...I would also accept Cashiers Check or Cash if local.
Contact Info:Feel free to PM me...Or my personal email is Teh.brandon@yahoo.com... or call my cell @ 9183610920
Recently I have decided to sell my project 415ci C5 build due to the starting of a new project. That said I've sold everything with the exception of these heads. Ive sold my Vic Jr with spray bars and 6061 elbow(on yellowbullet)/Ported LS2 TB(LS1tech)/injectors(LS1tech)/shortblock,trans,rear,roller with all accessories(locally). All that's left are my extremely nice heads.
These come fully assembled and ready to bolt on all that is needed are rockers.
I really liked these heads and I wouldnt be selling them if I didnt have an opportunity for another project. Therefore I'm looking to off load these sooner than later
These are a very nice aftermarket cast head. Here is a link to the PDF provided by All-Pro with detailed information on the heads:
http://www.allproheads.com/images%20...LS1-2_2-08.pdf
Specs specific to this item:
Aftermarket Cast...thick deck good for F/I or Nitrous
244cc runners
Ferrera Stainless Competition Valves 2.08/1.60
Comp Cams dual valve springs/Ti retainers
8mm bronze valve guides (provided by All-Pro)
Locks and Shims (provided by Folks Auto Machine)
Milled to 62cc
Competition Valve Job
Ported intake and exhaust ports(all port work/assembly done by Folks Auto Machine)*these flowed 354@.600
Folks also did some work to the Spark Plug Ports for better alignment
Pictures
AS CAST FROM ALL-PRO
VALVE GUIDES
AFTER PORTING-INTAKE
EXHAUST
CHAMBERS
I can take more pictures upon request...don't hesitate to contact me with any questions or concerns. Thanks
Brandon
Last edited by awd2rwd; 08-29-2011 at 09:50 AM.
#4
Launching!
Thread Starter
iTrader: (17)
Join Date: Jun 2006
Location: Tulsa, Ok
Posts: 251
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I run into some problems with there website sometimes....see if this link below works better.
http://www.allproheads.com/images%20...LS1-2_2-08.pdf
I would suggest using them on a 4+bore as that is what they are best suited for and what you would see full potential on but you can still use these on a 346ci. Ill try to find this thread over on yellowbullet discussing big bore heads on smaller cubic inch setups.
Feel free to contact me with any other questions.
Thanks
Trending Topics
#13
Launching!
Thread Starter
iTrader: (17)
Join Date: Jun 2006
Location: Tulsa, Ok
Posts: 251
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Not sure if the previous pictures were showing up as I think my album was set to private....if someone could let me know if the pictures are showing up that would be great
![Bang Head](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_banghead.gif)