Shreveport, LA area : 383 iron block LS1 & many other parts for sale
07-22-2013, 05:28 PM
#1
14 Second Truck Club
Thread Starter
iTrader: (6)
Join Date: Sep 2002
Location: Bossier City, LA
Posts: 2,343
Likes: 0
Received 0 Likes
on
0 Posts
Shreveport, LA area : 383 iron block LS1 & many other parts for sale If anybody needs the the following, let me know. I need to get rid of a bunch of stuff. I live in Bossier.
Big Red 2 ton engine hoist & HFT load leveler - $150
4L60-E trans pan-stock capacity, no drain bung drilled - $10
5.3 stock truck intake & engine cover (off of a 1999 silver ado - cleaned inside & out, in good shape - $75
130amp alternator 99-02 style - make offer
Newer style 07 & up water pump- make offer
2005 GM Truck Fans w/ old Nelson fan harness - $300
1999 5.3 engine oil pan - $75
New truck pick- up oil tube - $35
MSD GM Truck 99 & up ignition wires ( very low miles) - $50
LaPole Mid-length headers for 1999-2002 model GM trucks, 1 3/4" primaries - $100
8.1 marine 42lb injectors (Truck Height), need to be sent off for clean & rebuild - $100
1998 LS1 bare block (junk block left outside, would be great for a mock-up project - make offer
Brand new Iron Shortblock 383 LS1 (5.3 block bored & sonic tested, powder coated grey, built by Arrowhead Machine Shop in El Dorado, AR) been covered in an engine bag & kept inside my house on a crate & hand truck. Was gonna be put in my truck, due to life-changing situations, I won't be able to anymore.
-3.903" Mahle -6cc Flat Top Pistons
-Total Seal Rings
-4.000" Eagle Crank
-6.125" Scat Rods
-ARP Mains
-Schumacher high volume oil pump
-Rollmaster Double Roller Timing Chain
-Matching Powdercoated Front Engine Cover
-Futral F13 Cam (230/232-.595/.585-114+4*)
All the above is installed, also have a brand new Rear Engine cover, rear gasket & seal.
The rotating assembly is out of my old aluminum 383, all parts were thoroughly inspected & in spec, except one of the original rods that was slightly out of spec & replaced with a new one. Took me over a year and a half for the funds & build time.
I have no way to transport or lift into my car, so buyer must be able to pick up. - $3000 Firm
Big Red 2 ton engine hoist & HFT load leveler - $150
4L60-E trans pan-stock capacity, no drain bung drilled - $10
5.3 stock truck intake & engine cover (off of a 1999 silver ado - cleaned inside & out, in good shape - $75
130amp alternator 99-02 style - make offer
Newer style 07 & up water pump- make offer
2005 GM Truck Fans w/ old Nelson fan harness - $300
1999 5.3 engine oil pan - $75
New truck pick- up oil tube - $35
MSD GM Truck 99 & up ignition wires ( very low miles) - $50
LaPole Mid-length headers for 1999-2002 model GM trucks, 1 3/4" primaries - $100
8.1 marine 42lb injectors (Truck Height), need to be sent off for clean & rebuild - $100
1998 LS1 bare block (junk block left outside, would be great for a mock-up project - make offer
Brand new Iron Shortblock 383 LS1 (5.3 block bored & sonic tested, powder coated grey, built by Arrowhead Machine Shop in El Dorado, AR) been covered in an engine bag & kept inside my house on a crate & hand truck. Was gonna be put in my truck, due to life-changing situations, I won't be able to anymore.
-3.903" Mahle -6cc Flat Top Pistons
-Total Seal Rings
-4.000" Eagle Crank
-6.125" Scat Rods
-ARP Mains
-Schumacher high volume oil pump
-Rollmaster Double Roller Timing Chain
-Matching Powdercoated Front Engine Cover
-Futral F13 Cam (230/232-.595/.585-114+4*)
All the above is installed, also have a brand new Rear Engine cover, rear gasket & seal.
The rotating assembly is out of my old aluminum 383, all parts were thoroughly inspected & in spec, except one of the original rods that was slightly out of spec & replaced with a new one. Took me over a year and a half for the funds & build time.
I have no way to transport or lift into my car, so buyer must be able to pick up. - $3000 Firm
