What are signs of a failing camshaft position sensor?
#2
On The Tree
iTrader: (7)
Join Date: Nov 2005
Location: hennessey ok
Posts: 143
Likes: 0
Received 0 Likes
on
0 Posts
the camshaft postion sensor is behind the intake the easyest way to change it is pull the intake and and its one bolt i think its 10mm unscrew it pull it out put the new one in tightnin back down and go on
The following users liked this post:
kingcamaro (04-21-2021)
#5
Originally Posted by black1999-z28
the camshaft postion sensor is behind the intake the easyest way to change it is pull the intake and and its one bolt i think its 10mm unscrew it pull it out put the new one in tightnin back down and go on
Originally Posted by mr2guru
a code?
Here is a list of symptoms, that is leading me to the sensor:
- occasional backfire
- occasional popping
- occasional flashing SES (plugs, wires & coils are perfect)
- at certain startups, the car will run terrible, upon acceleration there is hesitating & stumbling.
Problems were intermittent, but are becoming more frequent.
My thoughts are the camshaft position sensor may be dying out, but not enough to throw a code or shut down the car completely.
Last edited by Michael02hawk; 08-22-2006 at 07:40 AM.
#7
TECH Fanatic
iTrader: (1)
Join Date: Nov 2002
Location: Venice, Ca
Posts: 1,829
Likes: 0
Received 0 Likes
on
0 Posts
With a bad sensor the car will hesitate, run very rich, and back fire. The cam sensor controls timing for cylinders 2-8, and the crank sensor sets for number 1. I would check wiring for pinches or burnt wires. May want to start by swaping the cam sensor if the wiring for crank and cam sensor look to be ok. The cam sensor is very sensitive and any marks on it will not let it work correctly.
Trending Topics
#8
TECH Enthusiast
iTrader: (12)
Join Date: Sep 2004
Location: Danville, VA
Posts: 684
Likes: 0
Received 0 Likes
on
0 Posts
a faulty camshaft position sensor will cause hard starts, and your fuel economy would be way down, because your injectors would go into "batch fire" spraying all of them on one bank at the same time hoping to catch an intake valve open.
this might sound dumb, but make sure that it is plugged in properly.
this might sound dumb, but make sure that it is plugged in properly.
#10
Okay, so I yanked off the intake manifold & removed the camshaft sensor.
The wires look fine, not pintched or broken & the sensor itself 'looks' okay, Im not sure if one can tell if its damaged or not, visually.
Anyway I can test this thing?
The wires look fine, not pintched or broken & the sensor itself 'looks' okay, Im not sure if one can tell if its damaged or not, visually.
Anyway I can test this thing?
Last edited by Michael02hawk; 08-22-2006 at 09:57 PM.
#12
Launching!
iTrader: (11)
Join Date: Nov 2004
Location: baton rouge,la
Posts: 290
Likes: 0
Received 0 Likes
on
0 Posts
i think i have a bad one too.my car is showing all those symtoms.fuel pressure is fine,but my car dont want to fire up on the first try.
where is the best place to get a new one?will oreilys be fine?
where is the best place to get a new one?will oreilys be fine?
#13
10 Second Club
iTrader: (15)
Join Date: Nov 2001
Location: St. Michael, MN.
Posts: 4,519
Likes: 0
Received 0 Likes
on
0 Posts
If you have a bad cam sensor you will throw at least 1 of 3 different codes. The car can still start with a bad sensor, but it will take excessive cranking. You mentioned a flashing SES light; what codes are recorded?
#14
Originally Posted by DrkPhx
If you have a bad cam sensor you will throw at least 1 of 3 different codes. The car can still start with a bad sensor, but it will take excessive cranking. You mentioned a flashing SES light; what codes are recorded?
LS1 edit showed a '34' and '43'. Which translate into P0340 & P0430:
P0340 Camshaft Position Sensor Circuit Malfunction
P0430 Catalyst System Efficiency Below Threshold (Bank 2)
Anyway, it wasnt easy to find one of these locally - but I managed. I'll pick up the replacement part this afternoon, and get it installed & put back together tonight.
With a little (okay, with a lot) of luck, it'll clear all this up.
#18
Well, no luck. I'm still having the same problem with the car.
But, I have been able to understand when its going to act up, and when it'll run okay.
If the car has been sitting for a while, basically cold, it'll start up, idle and run A+.
Its when I've parked it, for a 'short' period of time, like 2-5 mins or so, then start it back up (warm). It will still start up, run and idle good enough, but when dirving away is when it'll be fighting me, choking, studdering, etc!
If I shut it back off, & start it uo again, it'll probably be okay, if not, a 3rd shut down/start up will clear it up.
Anyone have a clue what is going on with this thing???
But, I have been able to understand when its going to act up, and when it'll run okay.
If the car has been sitting for a while, basically cold, it'll start up, idle and run A+.
Its when I've parked it, for a 'short' period of time, like 2-5 mins or so, then start it back up (warm). It will still start up, run and idle good enough, but when dirving away is when it'll be fighting me, choking, studdering, etc!
If I shut it back off, & start it uo again, it'll probably be okay, if not, a 3rd shut down/start up will clear it up.
Anyone have a clue what is going on with this thing???
#20
Originally Posted by Viper
If you've been recording the misfires in a log, swap injectors for the one that's misfiring the worst. You can get a noid light too to make sure all 8 injectors are firing, the light runs $30-$60.
I havnt heard of it before.