PCM Diagnostics & Tuning HP Tuners | Holley | Diablo
Sponsored by:
Sponsored by:

Need some help

Thread Tools
 
Search this Thread
 
Old 06-25-2007, 12:17 PM
  #1  
Teching In
Thread Starter
iTrader: (13)
 
creaper's Avatar
 
Join Date: Jun 2007
Location: Alexandria, VA
Posts: 33
Likes: 0
Received 0 Likes on 0 Posts
Default Need some help

I just purchased this car this past week. First off it is a 2001 camaro z28 with a procharger on it, full exhaust with o2 sims. I am having a problem with two codes. p0171 and p0174, System Too Lean (Bank 1 and 2). I have looked at the MAF and it is clean as far as i can tell but plan on spraying it with some brake cleaner here soon. Also looked to check for any vacuume leaks but have not found any. I do have the autotap system but unsure what the correct values i need or which ones i need to be looking at. Also has an aftermarket fuel pump that came with the procharger installed and is reading 60 psi, has a boost guage that reads 30psi of vacuume when idle and goes up as i hit the gas, and has a air/fuel guage that stay pegged out on rich. When i first got it the A/F would move around like normal but now it doesnt. Somebody help me out here.
Old 06-25-2007, 01:40 PM
  #2  
Teching In
Thread Starter
iTrader: (13)
 
creaper's Avatar
 
Join Date: Jun 2007
Location: Alexandria, VA
Posts: 33
Likes: 0
Received 0 Likes on 0 Posts
Default

cleaned the MAF and still same problem.
Old 06-25-2007, 02:28 PM
  #3  
TECH Addict
iTrader: (10)
 
wait4me's Avatar
 
Join Date: Feb 2003
Location: warsaw, in
Posts: 2,961
Likes: 0
Received 1 Like on 1 Post

Default

sounds like you might have a bad fuse for power on the o2s, Or you killed them from running too rich, or the tune is just way off.
Old 06-25-2007, 02:31 PM
  #4  
Teching In
Thread Starter
iTrader: (13)
 
creaper's Avatar
 
Join Date: Jun 2007
Location: Alexandria, VA
Posts: 33
Likes: 0
Received 0 Likes on 0 Posts
Default

where would i find the fuse for the o2's?
Old 06-25-2007, 02:43 PM
  #5  
TECH Senior Member
 
2001NBMZ28's Avatar
 
Join Date: Dec 2001
Location: Jacksonville, FL
Posts: 5,399
Likes: 0
Received 3 Likes on 3 Posts

Default

Just for the heck of it check the ENG SEN fuse - MAF and 02 are on the same circuit.
Old 06-25-2007, 02:56 PM
  #6  
Teching In
Thread Starter
iTrader: (13)
 
creaper's Avatar
 
Join Date: Jun 2007
Location: Alexandria, VA
Posts: 33
Likes: 0
Received 0 Likes on 0 Posts
Default

checked my fuses in the cab and the two boxes under the hood and they are all good. Didn't see a fuse labeled for the O2 sensors though.
Old 06-26-2007, 12:03 PM
  #7  
Teching In
Thread Starter
iTrader: (13)
 
creaper's Avatar
 
Join Date: Jun 2007
Location: Alexandria, VA
Posts: 33
Likes: 0
Received 0 Likes on 0 Posts
Default

anybody else wanna help me out? i already checked all the fuses and none were popped and also checked all the vacuum lines and didn't find any disconnected or loose.




All times are GMT -5. The time now is 10:16 PM.