Trans Am LED Fog Light Install (Morimoto Knockoffs)
#261
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Got the foglights yesterday. They are definitely not the ones pictured on the Amazon page that I ordered from. The Amazon pictures showed the pigtail at the bottom middle, but the ones I got have the pigtail on the side, taking up part of the fin I need to drill through. There is also a fin that runs horizontally right through the middle. From what I can tell the versions I received are the worst possible ones for this project.
For what it's worth both sets I've owned were purchased through eBay. If you happen to go that way I'd definitely message them and make sure they're just like pictures.
#265
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
So from what i have read, a 3/16 drill bit was used to go through the heatsink for a bolt?????????????????
i saw these but naturally no reviews:
i saw these but naturally no reviews:
Last edited by camar0rs; 05-21-2017 at 07:26 AM.
#269
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Not that I'm aware of.... But I'd guess the brackets and lights very well could be the same.
Measure your fog OD and if it's 4.5" then likely are the same. If I was you, just to double check I'd remove the 3 push pins on back/bottom of the bumper and shine a light up there and you should be able to see most of the bracket and compare to my pictures.
Measure your fog OD and if it's 4.5" then likely are the same. If I was you, just to double check I'd remove the 3 push pins on back/bottom of the bumper and shine a light up there and you should be able to see most of the bracket and compare to my pictures.
#270
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
https://ls1tech.com/forums/appearanc...l#post19653111
here you can get fogs for $39.99, followed basically same steps on post 1.... turned out good
here you can get fogs for $39.99, followed basically same steps on post 1.... turned out good
#271
TECH Enthusiast
iTrader: (13)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
so my fog lights are different and making it difficult.
![Name: fog%20lights3.jpg
Views: 1780
Size: 106.2 KB](https://ls1tech.com/forums/attachments/appearance-detailing/583255d1501198233-trans-am-led-fog-light-install-morimoto-knockoffs-fog-20lights3.jpg)
![Name: fog%20lights2.jpg
Views: 1784
Size: 116.5 KB](https://ls1tech.com/forums/attachments/appearance-detailing/583256d1501198233-trans-am-led-fog-light-install-morimoto-knockoffs-fog-20lights2.jpg)
![Name: fog%20lights1.jpg
Views: 1769
Size: 181.2 KB](https://ls1tech.com/forums/attachments/appearance-detailing/583262d1501198896-trans-am-led-fog-light-install-morimoto-knockoffs-fog-20lights1.jpg)
by where I drilled the holes there are humps in the housing and I have to grind them down to get the spacer to fit. and I have to trim the base of the nuts that im using so they line up with the hole I drilled. the nuts have a skirt. the cooling fins aren't very deep. I plugged one in and it didn't look that bright. but it was in my garage during the daytime. I still plan to make them fit and in the future do the low beam projectors.
![Name: fog%20lights3.jpg
Views: 1780
Size: 106.2 KB](https://ls1tech.com/forums/attachments/appearance-detailing/583255d1501198233-trans-am-led-fog-light-install-morimoto-knockoffs-fog-20lights3.jpg)
![Name: fog%20lights2.jpg
Views: 1784
Size: 116.5 KB](https://ls1tech.com/forums/attachments/appearance-detailing/583256d1501198233-trans-am-led-fog-light-install-morimoto-knockoffs-fog-20lights2.jpg)
![Name: fog%20lights1.jpg
Views: 1769
Size: 181.2 KB](https://ls1tech.com/forums/attachments/appearance-detailing/583262d1501198896-trans-am-led-fog-light-install-morimoto-knockoffs-fog-20lights1.jpg)
by where I drilled the holes there are humps in the housing and I have to grind them down to get the spacer to fit. and I have to trim the base of the nuts that im using so they line up with the hole I drilled. the nuts have a skirt. the cooling fins aren't very deep. I plugged one in and it didn't look that bright. but it was in my garage during the daytime. I still plan to make them fit and in the future do the low beam projectors.
#272
On The Tree
Join Date: May 2004
Location: Orlando, FL
Posts: 183
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Just wanted to add that I ordered mine on Amazon last week and ended up with the 'difficult' ones as well, so it would seem it's now difficult to get the older type. I'm sure I can make these work though.
#275
#278
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Success! Bought these off of eBay and received the old style.
http://m.ebay.com/itm/252174151609?_mwBanner=1
\
http://m.ebay.com/itm/252174151609?_mwBanner=1
\
Awesome! Really had no plans on doing this mod but for $36 why not? Just ordered a set.
Non-mobile clickable link:
http://www.ebay.com/itm/252174151609
#280
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Got mine in the mail today. Bought them from the link two or three posts above (eBay). They are in fact the OLD style that OP used so buy them up while you can.
Looking forward to doing this mod, maybe this weekend!
Looking forward to doing this mod, maybe this weekend!