BBC Block and Head recomendation
BBC Block and Head recomendation i have 4,350" Pistons,can i bore it that large .100 over or do i need to sleeve it,how thick are the walls in general and is there a specific block casting i should look for?
Head selection,is there any cheap good out there for FI?
Head selection,is there any cheap good out there for FI?
Trending Topics
Ari G since you arent paying attention to what anyone says. And **** you dont even type in complete thoughts. As I said before if you are buying a used motor it all depends on the block. Or you could do it right and buy a Dart big M block. Since I am guessing you have a set of pistons. I honestly dont know what the **** you are asking or even wtf you are trying to do.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo 
******* clueless.with minimal coreshift and such. im sure he knows hes not going to get one at the dealership parts counter.
those ***** are no help either. u have to go up there with parts numbers, or ask for exploded views of ****. they never know squat
the place i get my 6.0s
i saw some 90's duallys with efi bbc motors i think they were 454,iirc
i just go for the lsx engines. so i just glanced the bbc trucks.
but if i were to go bbc, i think my best option would be a dart block.
he should prolly just look into a dart, but i will call and see what the 454's go for.
i still think he just build up a 6.0 based motor with l92 heads
i saw some 90's duallys with efi bbc motors i think they were 454,iirc
i just go for the lsx engines. so i just glanced the bbc trucks.
but if i were to go bbc, i think my best option would be a dart block.
he should prolly just look into a dart, but i will call and see what the 454's go for.
i still think he just build up a 6.0 based motor with l92 heads
Smartmouth stop making **** up and twisting my words and acting like a child-i´ve been in sbc-lsx & import so i don´t know the perferd castings in BBC, and don´t really much care exept if i finde one in a car
What do you do for a living to be telling people you don´t know "how" to build an engine?
Anyway if you ask a simple "stupid" queston you most offen finde out who not to ask
Los:
I need a big cid engine thats the only reason why i´m using it and get the parts cheap
I got my wiseco custom FI pistons new for 100$ :mrgreen:,even cheaper then yours and THAT is a bargain
ok,thx buddy
What do you do for a living to be telling people you don´t know "how" to build an engine?
Anyway if you ask a simple "stupid" queston you most offen finde out who not to ask
Los:
I need a big cid engine thats the only reason why i´m using it and get the parts cheap
I got my wiseco custom FI pistons new for 100$ :mrgreen:,even cheaper then yours and THAT is a bargain
ok,thx buddy
See the cylinder head pic above, it says PASS, that means passenger car. This engine was factory installed in a motorhome.
Get it through your thick head, most 454's are the same from 70's to 1990 no matter what they were installed in.
I even got one out of a big *** generator, said hi perf pass on the block.
You're asking questions, I'm answering. What the **** else do you want.
Get it through your thick head, most 454's are the same from 70's to 1990 no matter what they were installed in.
I even got one out of a big *** generator, said hi perf pass on the block.
You're asking questions, I'm answering. What the **** else do you want.
What is your problem,i just asked a simple queston about castings how big you can go and head casting thats all!!!! **** off and bother sombody else with your smart mouthing
Smartmouth stop making **** up and twisting my words and acting like a child-i´ve been in sbc-lsx & import so i don´t know the perferd castings in BBC, and don´t really much care exept if i finde one in a car
What do you do for a living to be telling people you don´t know "how" to build an engine?
Anyway if you ask a simple "stupid" queston you most offen finde out who not to ask
Los:
I need a big cid engine thats the only reason why i´m using it and get the parts cheap
I got my wiseco custom FI pistons new for 100$ :mrgreen:,even cheaper then yours and THAT is a bargain
ok,thx buddy
What do you do for a living to be telling people you don´t know "how" to build an engine?
Anyway if you ask a simple "stupid" queston you most offen finde out who not to ask
Los:
I need a big cid engine thats the only reason why i´m using it and get the parts cheap
I got my wiseco custom FI pistons new for 100$ :mrgreen:,even cheaper then yours and THAT is a bargain
ok,thx buddy
