LivernoisMotorsports

iTrader: (1)

We have all of these items in stock and are offering deep discounts. Please PM me for pricing and include the part and part # you are inquiring about. There are limited quantities available.

Halltech

The Halltech Stinger Intake System is one of the best performance upgrades available for the 1997-2004 C5 and Z06 Corvette. Their air filter and the tunnel bridge (or power duct) increases airflow by 25 % over stock, and replaces the stock air bridge, which is the most restrictive part of the C5/Z06 intake system. With the 100 mm straight shot at the throttle body and 15% more plenum volume, coupled with the largest filter ever made for the C5/Z06, you will feel the power. This system is designed for simple installation at the end of the MAF and throttle body. No cutting, modifying or lift required to install. Kit carries a lifetime warranty. Ease of installation and cost, make this one of the most popular Corvette intakes ever.



Stinger CAI Part #W1010

1997-00 C5 Corvette - Black

Stinger CAI Part #W1009

1997-00 C5 Corvette - Red

Stinger CAI Part #W1017

2001-04 C5 Corvette - Black

Stinger CAI Part #W1018

2001-04 C5 Corvette - Red

Innovate Motorsports

XD 16 Stand Alone Gauge Part #3780

The Innovate XD-16 dash-mountable Digital Display ships as an AFR gauge, but can also be configured to display any channel of the Modular Tuning System. Key features:

* 2 Bezels + 8 faces = 16 combinations (see below)
* 3/4” thick, so it's possible to mount even in surface mount configurations
* 3-character LED display -Record/Calibrate/Peak Hold button
* Programmable (values and colors) digital needle
* Billet Aluminum bezel



Innovate Data Acquisition, LC-1 Lambda Cable with O2 Sensor, Stand-Alone Wideband Controller. Part #3769

These Innovate LC-1 Lambda cables with O2 sensor are complete wideband controllers built into a sealed cable. They feature the same award-winning patented digital measurement principal found in the LM-1, and include digital input, output, and 2 programmable analog outputs.



Innovate Motorsports G-Series Air/Fuel Gauge Kits Part # 3801

The G-Series Air/Fuel Gauge Kits feature a high-speed stepper motor, through-dial backlighting, and an illuminated pointer. Kits include Innovate's LC-1 wideband controller, oxygen sensor and bung/plug, and LogWorks engine-tuning software.

Benefits and Features:
# The industry's most accurate and fastest-responding wideband controller
# Illuminated needle and through-dial backlighting
# One additional analog output (one connects to the gauge)
# Easy set up and wiring
# Log directly from the LC-1's digital output into laptop with included software



Innovate Part # 3726 Add-on Wideband Sensor Accs .




Innovate Part # 3728. Exhaust Clamp

Venturi-effect, tapped exhaust clamp for obtaining accurate lambda measurements in non-cat autos or other engines.




Innovate Motorsports Part #3739 18-ft. Sensor Cable (LM-1 Only)

To Minimize the effects of noise coupling with the extended-length sensor cable, Innovate recommends minimizing the length of the power-supply cable. <2’ is ideal. Noise coupling may be present if the bar graph is flickering. Excessive coupling will result in sensor errors.



Innovate Part # 3730 6-ft. long, mini to stripped-and-tinned, matching LM-1 analog output specifications.

The cable has (2) Analog Outputs 0-5 volts that are fully programmable with the LM-1 software.



Innovate Part # 3760. INNOVATE CABLE: DAISY CHAIN XD-1 OR LC-1

This custom cable will allow you to connect and/or daisy chain the following products: XD-1, LC-1, LMA-3, ST-12. Also used to connect the LM-1 to the XD-1.




Innovate Part # 3759. Din 8 to Female 2.5. LM-1 to XD-16



Innovate Part # 3741 Serial Cable




Innovate Motorsports AC Wall Adapter P/N 3732

For the Innovate LM-1 digital air fuel meter only.

Used to power your LM-1 from the outlet in the shop



Innovate Part # 3734 10-ft. long, for direct connection on LM-1 to auto or motorcycle battery.




Innovate Part # 3771 LM-1 Battery Pack

This battery pack enables testing/logging without having to hook the LM-1 to a 12-volt source. Complete with charger, the foam-lined pack is heavy-duty plastic with a built-in rechargeable battery. It's ideal for sprint cars, midgets and quarter midgets, go-carts, motorcycles, or applications where a battery does not exist or is difficult to access.



Thank you

Rick LeBlanc
Livernois Motorsports

LivernoisMotorsports

iTrader: (1)

All pm's replied to. I also have the following Kooks Products:

KOOKS C5 (1997-2000) 1 7/8 x 3 Headers Part #6103 (*WITH AIR TUBES AND 02 FITTINGS* WITH MERGE COLLECTORS )

KOOKS CORVETTE (C5/Z06) X STAINLESS SYSTEMS - OFF ROAD- 2 1/2" X Pipe OEM Connection- (CORVETTE BOLT IN 3 PC X-CROSSOVER: INCLUDES X-CROSSOVER, MID SECTIONS AND HARDWARE) Part #6106S

KOOKS 1-3/4" Long-Tube Race Headers With 3" Collectors - Corvette C5- Part #6100

KOOKS 1998-2002 F-Body, 3" Stainless Steel Catalytic Y-Pipe Part # 6502MS

KOOKS 98-99 F Body 1-3/4 x 3 inch Stainless Headers Part #6500S

KOOKS 98-02 F Body 1 7/8 x 3 - Stainless Race Header- Part # 6501RHS

KOOKS 98-02 Fbody LS1 Race Headers - 1-3/4" x 3" no AIR fittings, O2 fittings only. Part #6500RHS

KOOKS Headers, 2006 Trialblazer SS, 1-3/4"x3" Stainless Steel Headers Part #6310

KOOKS Y-Pipe w/ Metallic Cats, Stainless Steel, 3" Inlets, 3" Outlet Trailblazer SS- Part #6312-CC

KOOKS Y-Pipe OFF ROAD, SS, 3" inlets, 3" outlet Trailblazer SS- Part # 6313-OC

Thank you,

Rick LeBlanc
Livernois Motorsports