1996 Trans Am roller
#21
Banned
Thread Starter
iTrader: (13)
Join Date: Jan 2008
Location: Alvin,Tx
Posts: 179
Likes: 0
Received 0 Likes
on
0 Posts
Well getting some good interest in parts so parting out may be the new route. Also have an upgraded 4l60 for lt1 for sale. Has upgraded bands, servo, shift kit for sale too. Came out of my cousins impala. Had prolly 10k or so on it and shifted perfectly when pulled. Asking 600.
#25
Banned
Thread Starter
iTrader: (13)
Join Date: Jan 2008
Location: Alvin,Tx
Posts: 179
Likes: 0
Received 0 Likes
on
0 Posts
condensor
radiator
front bumper cover sand it down and paint and fix the tear and you have a good new one.
about a 2'' tear
middle console
small crack in the middle console
rear filler panel
drivers side tail light
rear bumper
y-pipe with bullet style muffler installed (previous owner did it)
drivers side door panel (excuse the speaker grille)
headers (not pacesetter as they have a slip on collector) beleve this are jet hot shoot me a PM for the price.
MAF sensor
drivers side headlight
ABS sensors
mirror
radiator
front bumper cover sand it down and paint and fix the tear and you have a good new one.
about a 2'' tear
middle console
small crack in the middle console
rear filler panel
drivers side tail light
rear bumper
y-pipe with bullet style muffler installed (previous owner did it)
drivers side door panel (excuse the speaker grille)
headers (not pacesetter as they have a slip on collector) beleve this are jet hot shoot me a PM for the price.
MAF sensor
drivers side headlight
ABS sensors
mirror
#26
Banned
Thread Starter
iTrader: (13)
Join Date: Jan 2008
Location: Alvin,Tx
Posts: 179
Likes: 0
Received 0 Likes
on
0 Posts
fuse panel cover
guage cluster
radio bezel/hvac controls
dash pad
headlight switch
a/c vents NOT broken
window switches/door locks
power steering reservoir
alternator good and charges
LS1 induction bottom
a/c compressor and bracket
these are the wheels
back seats
sorry the car is dusty. If you see anything else in the pics not listed dont hesitate to ask!
#31
Banned
Thread Starter
iTrader: (13)
Join Date: Jan 2008
Location: Alvin,Tx
Posts: 179
Likes: 0
Received 0 Likes
on
0 Posts
Headers/tranny/motor are now up for sale!
4l60 for LT1 w/ 10k miles on it with upgraded bands/servos/etc asking 600$
355 ci motor with forged pistons, stock rods,crank, ARP hardware, fresh bearings,rings, oil pump, fresh water pump, comes with upgraded injectors as well, also has GTP stage II ported/polished heads (flow 290cfm 19x) have upgraded beehive springs, Comp cams new rockers, upgraded pushrods, ARP bolts, CC306 camshaft. This motor has break in mileage! Pulled the valve cover off and still has assembly lube in the oil. Has a ported LT4 intake on top with a 58mm BBK throttle body.
4l60 for LT1 w/ 10k miles on it with upgraded bands/servos/etc asking 600$
355 ci motor with forged pistons, stock rods,crank, ARP hardware, fresh bearings,rings, oil pump, fresh water pump, comes with upgraded injectors as well, also has GTP stage II ported/polished heads (flow 290cfm 19x) have upgraded beehive springs, Comp cams new rockers, upgraded pushrods, ARP bolts, CC306 camshaft. This motor has break in mileage! Pulled the valve cover off and still has assembly lube in the oil. Has a ported LT4 intake on top with a 58mm BBK throttle body.
#38
How much for the complete dash (minus the broken dash cover), the gauge cluster, the HVAC, and the headlight switch. I will also need the headlight switch plug with some of the wires attached (6" if possible), the cluster plug with some of the wires attached, and the HVAC plugs with wires.
If you could get me a price for everything I'd appreciate it. Thanks in advance
If you could get me a price for everything I'd appreciate it. Thanks in advance
#39
TECH Fanatic
iTrader: (8)
Join Date: Sep 2007
Location: Hillsboro Kansas
Posts: 1,823
Likes: 0
Received 0 Likes
on
0 Posts
heres how it sits in its current form. Picking it up from a buddy of mine. Fresh 6spd in the car as well as some other goodies. I will post up a sound clip of it when we pick it up next weekend. I already have some of the front pieces needed to complete it. It was a deal tho trust me