383 SBC Part Out
#1
383 SBC Part Out
Ohio Crankshafts 383 Super Kit Cost $2000 will sell for $1500.
- Crank checked out good, internal balanced, lightweight crank
- 6" H-Beam rods (NEW)
- SRP flat top pistons
- Total Seal Rings W/ Napier 2nd ring ($300 NIB)
- Clevite H-bearings (rods and mains)
"010" GM block clearanced for the above rotating asssembly, with main caps and New ARP main studs $250
Dart Pro1 230 aluminum heads. $1000
- New Red SS 2.08", +.100" long, Intake valves
- New Red Inkonel 1.625", +.100" long Exhaust valves
- Full race port
- hasnt been ran since rebuild
- 7/16 ARP rocker studs and 5/16" guide plates
- Crane cams valve springs (I had around a .560" lift sold flat tapped cam in it)
ARP SBC Head studs $150
Edelbrock Super Victor 4150 intake $200
- Port matched to a Fel-Pro 1206
- Ported out in the plenum too
- Drilled and tapped for a fogger (plugged off right now)
NOS kits/parts
- NOS Big shot kit $400 w/ bottle or $300 no bottle
- NOS fogger partial plumb kit missing 1 tube and jets $250
- 3 total bottles $100 each
- Nitrous Outlet Stinger Plate ONLY never used $300
Holley HP 750 $350
Canton 8 qt pan NIB w/ dip stick$200
MSD Pro Billet Distributor (locked out) with MSD 8.5 black wires $200
Billet Specialties front accessory drive kit w/ Chrome Power Master 100A one wire alt and power steering pump. $750
http://www.billetspecialties.com/ser...t-alt-and-p/s/
Billet Specialties SBC Satin Black valve covers $100
http://www.billetspecialties.com/val...vrolet-script/
Or $4500 for everything listed here
All parts located just south of Houston, TX
832-370-2381 ------- Don
- Crank checked out good, internal balanced, lightweight crank
- 6" H-Beam rods (NEW)
- SRP flat top pistons
- Total Seal Rings W/ Napier 2nd ring ($300 NIB)
- Clevite H-bearings (rods and mains)
"010" GM block clearanced for the above rotating asssembly, with main caps and New ARP main studs $250
Dart Pro1 230 aluminum heads. $1000
- New Red SS 2.08", +.100" long, Intake valves
- New Red Inkonel 1.625", +.100" long Exhaust valves
- Full race port
- hasnt been ran since rebuild
- 7/16 ARP rocker studs and 5/16" guide plates
- Crane cams valve springs (I had around a .560" lift sold flat tapped cam in it)
ARP SBC Head studs $150
Edelbrock Super Victor 4150 intake $200
- Port matched to a Fel-Pro 1206
- Ported out in the plenum too
- Drilled and tapped for a fogger (plugged off right now)
NOS kits/parts
- NOS Big shot kit $400 w/ bottle or $300 no bottle
- NOS fogger partial plumb kit missing 1 tube and jets $250
- 3 total bottles $100 each
- Nitrous Outlet Stinger Plate ONLY never used $300
Holley HP 750 $350
Canton 8 qt pan NIB w/ dip stick$200
MSD Pro Billet Distributor (locked out) with MSD 8.5 black wires $200
Billet Specialties front accessory drive kit w/ Chrome Power Master 100A one wire alt and power steering pump. $750
http://www.billetspecialties.com/ser...t-alt-and-p/s/
Billet Specialties SBC Satin Black valve covers $100
http://www.billetspecialties.com/val...vrolet-script/
Or $4500 for everything listed here
All parts located just south of Houston, TX
832-370-2381 ------- Don