FS: NICE show/race camaro ROLLER !
#1
TECH Resident
Thread Starter
iTrader: (52)
Join Date: Jan 2004
Location: DFW
Posts: 809
Likes: 0
Received 0 Likes
on
0 Posts
FS: NICE show/race camaro ROLLER !
Many people in DFW have seen this car. Was my dads ride for years tell i bought it from him. I don't have time or desire to put it together anymore. Building my vette now.
98 blue camaro 50k miles(z28/SS hood and spoiler)
Chassis / suspension
BMR turbo K member
BMR lower and upper A arms
BMR front and rear anti sway bars
powdercoated black front spindles
KONI adj. coilover front and rear with ground control
corvette zo6 front brakes
hawk pads/ drilled and slotted EBC rotors
DPE custom 1 off forged wheels
BIllingsly street 9 in rear
35 spline axles,Detroit locker,430 gear
WOLFE racecraft rear control arms, T arm, PHR
Walbro fuel pump with stainless lines up to engine(black braided inside engine bay)
aeromotive black regulator(only thing missing from fuel system is rails and injectors)
2002 plastic tank
2002 wiring harness and PCM
RON davis radiator($$$)
All accessories
Brand new AC compressor
custom base/clear coat engine bay and custom covers hiding fuse panel and wires
HID headlights and Fog lights
Linginfelter PCV catch can setup
Hiddin wiring harness in engine bay
Hiddin ABS module and brake lines
tick performance adj. master(new)
SHort throw shifter
stock 6 speed crossmember
MOSER aluiminuim driveshaft($$$)
stainless fasteners under the hood
INTERIOR
Black leather
gray ostrich inserts in seats and door panels
alpine Pop up screen
JL solo sub
mb quarts mids and highs
Escort radar system hard wired($$$)
lazer jammers in front and rear($$$)
You need a complete longblock and trans to put the car together.I have everything as far as hardware in boxes. I can total up $$ in parts here and it would blow your mind. Car is a true show and go car.Have a room full of trophies and plaques to prove it.
$9000(I honestly think i could part the car out and make this much,which I might do )
Bryan
Sorry these are the only two pics i have.
98 blue camaro 50k miles(z28/SS hood and spoiler)
Chassis / suspension
BMR turbo K member
BMR lower and upper A arms
BMR front and rear anti sway bars
powdercoated black front spindles
KONI adj. coilover front and rear with ground control
corvette zo6 front brakes
hawk pads/ drilled and slotted EBC rotors
DPE custom 1 off forged wheels
BIllingsly street 9 in rear
35 spline axles,Detroit locker,430 gear
WOLFE racecraft rear control arms, T arm, PHR
Walbro fuel pump with stainless lines up to engine(black braided inside engine bay)
aeromotive black regulator(only thing missing from fuel system is rails and injectors)
2002 plastic tank
2002 wiring harness and PCM
RON davis radiator($$$)
All accessories
Brand new AC compressor
custom base/clear coat engine bay and custom covers hiding fuse panel and wires
HID headlights and Fog lights
Linginfelter PCV catch can setup
Hiddin wiring harness in engine bay
Hiddin ABS module and brake lines
tick performance adj. master(new)
SHort throw shifter
stock 6 speed crossmember
MOSER aluiminuim driveshaft($$$)
stainless fasteners under the hood
INTERIOR
Black leather
gray ostrich inserts in seats and door panels
alpine Pop up screen
JL solo sub
mb quarts mids and highs
Escort radar system hard wired($$$)
lazer jammers in front and rear($$$)
You need a complete longblock and trans to put the car together.I have everything as far as hardware in boxes. I can total up $$ in parts here and it would blow your mind. Car is a true show and go car.Have a room full of trophies and plaques to prove it.
$9000(I honestly think i could part the car out and make this much,which I might do )
Bryan
Sorry these are the only two pics i have.
Last edited by sr71bbjr; 06-28-2011 at 03:25 PM.
#5
TECH Enthusiast
Dont suppose youd be willing to sell the DPE's seperate?