Morgan and Son. Anyone have experience ???
Morgan and Son. Anyone have experience ??? Good, bad, ugly??
I need my block bored, honed, decked. New Callie's crank, h beams and lunati pistons balanced
Rings bearings etc etc. basically short block build
Personal experiences would be bet but if you know a guy that knows a guy that had an issue that would be nice to know too
Also what rings would y'all suggest ( 8-15 psi. Street car)
I need my block bored, honed, decked. New Callie's crank, h beams and lunati pistons balanced
Rings bearings etc etc. basically short block build
Personal experiences would be bet but if you know a guy that knows a guy that had an issue that would be nice to know too
Also what rings would y'all suggest ( 8-15 psi. Street car)
I don't know anyone that uses them but, when I'm at the track I see them in a lot of cars.. I think the one that wins the triple threat all the time is the wife of the owner. I see them a lot at Kennedale , Dallas Raceway, Redline raceway.
Launching!
Joined: Mar 2008
Posts: 251
Likes: 0
Bud morgan is a freaking legend.
If you want your motor built with care, by a professional, clean, honest experienced engine builder, take it to morgan and sons. They usually build big horsepower big blocks nitrous but they have built engines used for turbo, spray and na, and have customers that run in numerous racing organizations across this great country.
If you want your motor built with care, by a professional, clean, honest experienced engine builder, take it to morgan and sons. They usually build big horsepower big blocks nitrous but they have built engines used for turbo, spray and na, and have customers that run in numerous racing organizations across this great country.
Last edited by Luckymex_dallas; Jan 30, 2013 at 04:35 PM.
I dropped everything off with them tonight... my only concern is the rings... I'm a guy that reads WAY too much into everything I find online and I have found that you don't want to use hellfire rings on a street car because they will eat up the cyl.... and you don't want to use Moly rings either... preferably a steel or something top ring.
he said plasma Moly rings... I figure I'll run 8-15psi so I need to figure out what I want to do on that part...
he said plasma Moly rings... I figure I'll run 8-15psi so I need to figure out what I want to do on that part...
Launching!
Joined: Mar 2008
Posts: 251
Likes: 0
i would trust him with the build and let him use what he thinks he should use.
you never know the reliabilty of a random person online, but your dealing face to face with a great engine builder, follow his lead.
tell em roman rodriguez with "the joker" reccommended them.
you never know the reliabilty of a random person online, but your dealing face to face with a great engine builder, follow his lead.
tell em roman rodriguez with "the joker" reccommended them.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
