Any ideas??

Thread Tools
 
Search this Thread
 
Old 06-11-2013, 06:38 PM
  #1  
Teching In
Thread Starter
 
Zyaa-99 m6's Avatar
 
Join Date: Oct 2012
Location: texas
Posts: 2
Likes: 0
Received 0 Likes on 0 Posts
Question Any ideas??

I took my camaro into G-force about a month ago,super cool guys!,had awesome service an was extremely happy with what I got
Tick stage 2 rebuild
New berrings
New 2,3,4,5,&R gears
New input shaft
Spec stage 2 clutch with billet flywheel
Rear main seal
Freeze plug
Pilot bearing
Tick clutch slave cylinder
Hurst billet plus short throw

I will be taking it back after what happened on my drive home today but just wanted some input on what y'all think...I have babied it sense I got it back I've got 1100 on it sense the rebuild...while driving home it popped out of 4th randomly then got to the stop light an it wouldn't go into 1st I pumped the clutch an nothing after had to start in 2nd.2nd-6th were fine..got to the next light an went into 1st no problem get home pull in the drive way with the car running tried to run threw the gears again start in 1st then its this werid dealing like its stuck in gear extremely hard 1st-4th finally get it into neutral an the sitck will not move side to side turn the car off an let it cool of for a few hours..I start it up the same thing now in just frustrated to no end after spending what I did babying it just for this to happen does anyone have any ideas?
Old 06-11-2013, 07:34 PM
  #2  
TECH Enthusiast
iTrader: (16)
 
05 GSXR 1XXX's Avatar
 
Join Date: Aug 2005
Location: Woodlands, TX
Posts: 516
Likes: 0
Received 0 Likes on 0 Posts

Default

Before posting this I would have called g force and see what they can do for you..

I don't think I've seen a bad post on here about them, I'm sure they will take care of you.
Old 06-11-2013, 08:50 PM
  #3  
Teching In
Thread Starter
 
Zyaa-99 m6's Avatar
 
Join Date: Oct 2012
Location: texas
Posts: 2
Likes: 0
Received 0 Likes on 0 Posts
Default

I didn't say anything bad about G-force I started off bysaying they were super cool an I was extremely happy with them...I never once talked s**t about them or their work...I explained what was going on asked if any one had any ideas on the situation.I said that "I" was frustrated with my situation (why the transmission was doing this) not G-FORCE *..
Old 06-11-2013, 09:08 PM
  #4  
TECH Regular
iTrader: (4)
 
camarochvy21's Avatar
 
Join Date: Jul 2005
Posts: 437
Likes: 0
Received 0 Likes on 0 Posts

Default

Your trouble shooting, got it. I have no idea what's wrong, give em a call
Old 06-11-2013, 09:14 PM
  #5  
Teching In
Thread Starter
 
Zyaa-99 m6's Avatar
 
Join Date: Oct 2012
Location: texas
Posts: 2
Likes: 0
Received 0 Likes on 0 Posts
Default

I didn't say anything bad about G-force I started off bysaying they were super cool an I was extremely happy with them...I never once talked s**t about them or their work...I explained what was going on asked if any one had any ideas on the situation.I said that "I" was frustrated with my situation (why the transmission was doing this) not G-FORCE *..
Old 06-11-2013, 09:16 PM
  #6  
Teching In
Thread Starter
 
Zyaa-99 m6's Avatar
 
Join Date: Oct 2012
Location: texas
Posts: 2
Likes: 0
Received 0 Likes on 0 Posts
Default

Didn't mean to post that twice an thanks chvy21
Old 06-12-2013, 11:26 AM
  #7  
TECH Fanatic
iTrader: (19)
 
imma_stocker's Avatar
 
Join Date: Apr 2007
Location: Country
Posts: 1,155
Received 36 Likes on 28 Posts

Default

Could be a bent fork, low fluid, air in the clutch lines.....

Long list of "could be" but G-Force has been good to me. Very honest from what I can tell.
Old 06-12-2013, 12:48 PM
  #8  
Teching In
Thread Starter
 
Zyaa-99 m6's Avatar
 
Join Date: Oct 2012
Location: texas
Posts: 2
Likes: 0
Received 0 Likes on 0 Posts
Default

Dropped it off this morning an they went straight to work on it...I've always heard great.things about them an after taking my car to them see why they are straight up guys I couldn't ask for a better experience just a speed bump in the road things happen an its all under warranty so not a big deal.will definitely be doing businesses with them again!
Old 06-12-2013, 01:46 PM
  #9  
On The Tree
iTrader: (1)
 
BSGTOLS2's Avatar
 
Join Date: Nov 2011
Location: PEARLAND, TX
Posts: 153
Likes: 0
Received 0 Likes on 0 Posts
Default

I too will be using them for a nitrous install and retune
Old 06-13-2013, 07:29 AM
  #10  
TECH Enthusiast
iTrader: (7)
 
Greed4Speed's Avatar
 
Join Date: Sep 2003
Location: Ft. Worth-ish
Posts: 600
Likes: 0
Received 0 Likes on 0 Posts

Default

Originally Posted by Zyaa-99 m6
Didn't mean to post that twice an thanks chvy21
You know you can delete posts, right?
Old 06-13-2013, 07:33 PM
  #11  
Teching In
Thread Starter
 
Zyaa-99 m6's Avatar
 
Join Date: Oct 2012
Location: texas
Posts: 2
Likes: 0
Received 0 Likes on 0 Posts
Default

Originally Posted by Greed4Speed
You know you can delete posts, right?
Nope, sure didn't .well turns out I bent a fork trying to force it.an I had a couple of messed up bronze pads..guys said they have never heard or seen such a thing with the pads their fixing it an should have it tomorrow. Just a bump in the road.but I would still highly recommend these guys to any one highly professional. Super friendly & helpful. An a nice clean shop. Top notch!



Quick Reply: Any ideas??



All times are GMT -5. The time now is 04:27 PM.