LS/M track meet
Gates open @ 7:00
Directions for those like me that haven't been there before
Northbound: Travel I-35 through Denton to Exit 474 (just pass Love's Truck Stop) stay on the service road it will U-turn underneath the interstate . Dragway will be on your right.
Southbound: South I-35 through Sanger take Exit 473 ( Love's Truck Stop) cross overpass stay on service rd. Dragway will be on your right.
Gates open @ 7:00
Directions for those like me that haven't been there before
Northbound: Travel I-35 through Denton to Exit 474 (just pass Love's Truck Stop) stay on the service road it will U-turn underneath the interstate . Dragway will be on your right.
Southbound: South I-35 through Sanger take Exit 473 ( Love's Truck Stop) cross overpass stay on service rd. Dragway will be on your right.
Whats up ! Just wanted to say hello . I wish I could come and put more time and effort into this club, but It was time to man up and work these hours. Know what I mean? I hope I can make it to a meeting real soon.. I plan on putting the Phantom under the knife this summer.
My turd is going partially under the knife, at least the rear for now. I'm leaning towards a Midwest Chassis fab 9". Bit overkill for me at the moment, but great peace of mind and something I can grow in to. How do you like the 3.90's? I've been wanting a gear set in that range.
bmxer,
I'll be out there late. I have to pick the wife up a the airport. Flight comes in around 6:45. It'll be 8 or so before I get to the track if it lands on time, but Gilbert should be out there. Anyway, I'll be rolling the TBSS in all it's stock glory.
My turd is going partially under the knife, at least the rear for now. I'm leaning towards a Midwest Chassis fab 9". Bit overkill for me at the moment, but great peace of mind and something I can grow in to. How do you like the 3.90's? I've been wanting a gear set in that range.
bmxer,
I'll be out there late. I have to pick the wife up a the airport. Flight comes in around 6:45. It'll be 8 or so before I get to the track if it lands on time, but Gilbert should be out there. Anyway, I'll be rolling the TBSS in all it's stock glory.
The 3.90's are good but not on a 28' tire ike I have its like I have 3.42's and with a 6 speed

I am planning on boosting it in near future though it all depends on what you want.
Spray vs. Boost
Spray I would go 4.11's to 4.56's with a 6 speed
Boost no higher than 3.90's
Trending Topics

I am planning on boosting it in near future though it all depends on what you want.
Spray vs. Boost
Spray I would go 4.11's to 4.56's with a 6 speed
Boost no higher than 3.90's
The Best V8 Stories One Small Block at Time
I know it isn't anythng remarkable but it's not bad for being completely stock, under 4k miles, and a 2 ton+ vehicle. I didn't even remove the spare, let the engine cool, drop tire pressure or anything. It was a better time than a newer Mustang GT ran....
I know it isn't anythng remarkable but it's not bad for being completely stock, under 4k miles, and a 2 ton+ vehicle. I didn't even remove the spare, let the engine cool, drop tire pressure or anything. It was a better time than a newer Mustang GT ran....

How was their track??? Was it sticky? could it use improvements ASAP?
The big bonus, I got 4 runs in an hour and could have done more. I only got 4 runs all day when I went to Ennis.
The track was cold, the guys at Northstar fought it all evening. We really are lucky to have folks like Nick and Larry who understand and recognize less than favorable track conditions and actually try to do something about it. One issue they had was the fact that they had scraped the track a few days ago and did were not able to get fresh rubber down.
That's drag racing though!
g



....stupid weather