Rollin Chassis For Sale
01-11-2006, 05:10 PM
#45
8 Second Club
iTrader: (10)
Join Date: Jan 2004
Location: Metro Detroit
Posts: 1,522
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 1QuickT-A
PM me with your bottom dollar... I'm thinking of selling my "almost" stock 99 T/A to buy a roller Z/SS Camaro to put my 408/TH400 in.. I'm not tryin to insult you in any way but, 13.5k is just too much in my opinion.. I wanted Futrals car which was the same setup as this and came with a built T-56 setup for $10k obo.. Let me know what you can do.. Thanks
01-11-2006, 05:16 PM
#46
8 Second Club
iTrader: (10)
Join Date: Jan 2004
Location: Metro Detroit
Posts: 1,522
Likes: 0
Received 0 Likes
on
0 Posts
Front Suspension
AJE K-member
Lower A-Arms
Spindles (2" Drop)
All AJE parts are Chromoly/Hyme joint
(roughly 1500)
Wolfe RaceCraft Travel limiters
HAL QA-1 Shocks with HAL Springs
Pinto Rack n pinion
(800-1000)
Rear Suspension
Wolfe Coil-Over spring mounts
Koni SPA1 Drag Shocks
Spohn Mild Steel LCA's with Reloc Brackets
" " " Crosmember mounted Torque Arm With DS Safety loop
Aluminum Panhard Bar
Spohn Drag Race anti-roll bar
(1500+)
Strange Race brakes on all 4 corners
Weld Alumistar Wheels 15x3.5 15x10
MT Sprtsman Fronts
MT ET Drag 28x10.5 (Old and need to be replaced before it see's the track again)
(3000 or so)
Rear Axle
Billingsley Fabed 9" ford (Narrowed 2" on each side)
Strange S-Series Nodular Center
" S/T 35 Spline Spool
S/T 35 Spline Axles
Richmond 4:30 Gears
inland empire 4130 yoke (3150 Joint)
Spohn Steel Driveshaft
(3500)
Interior
Kirkey Race Seats with grey tweed covers
RJS 5pt Harness for driver & Passenger
Tweed covered door panels
Many Interior parts wrapped in carbon fiber
Black carpet
(figure around 1000)
No Wiring for stereo
Al other factory wiring is intact
No HVAC
Factory PCM
Battery Relocated to Spare Tire well with master disconnect switch
(250)
Custom Chromoly Roll Cage with dash bar By Tim Bradham's Chassis Works.
(figure 2500)
Those are all low ballparks and that's over 14,000 in just parts. I'm sure I'm low on a lot of stuff too and that's not including any kind of installation besides installing the cage. It's definitly a great deal! People don't understand what it costs and how much time is involved in putting something like that together.
Good luck!
AJE K-member
Lower A-Arms
Spindles (2" Drop)
All AJE parts are Chromoly/Hyme joint
(roughly 1500)
Wolfe RaceCraft Travel limiters
HAL QA-1 Shocks with HAL Springs
Pinto Rack n pinion
(800-1000)
Rear Suspension
Wolfe Coil-Over spring mounts
Koni SPA1 Drag Shocks
Spohn Mild Steel LCA's with Reloc Brackets
" " " Crosmember mounted Torque Arm With DS Safety loop
Aluminum Panhard Bar
Spohn Drag Race anti-roll bar
(1500+)
Strange Race brakes on all 4 corners
Weld Alumistar Wheels 15x3.5 15x10
MT Sprtsman Fronts
MT ET Drag 28x10.5 (Old and need to be replaced before it see's the track again)
(3000 or so)
Rear Axle
Billingsley Fabed 9" ford (Narrowed 2" on each side)
Strange S-Series Nodular Center
" S/T 35 Spline Spool
S/T 35 Spline Axles
Richmond 4:30 Gears
inland empire 4130 yoke (3150 Joint)
Spohn Steel Driveshaft
(3500)
Interior
Kirkey Race Seats with grey tweed covers
RJS 5pt Harness for driver & Passenger
Tweed covered door panels
Many Interior parts wrapped in carbon fiber
Black carpet
(figure around 1000)
No Wiring for stereo
Al other factory wiring is intact
No HVAC
Factory PCM
Battery Relocated to Spare Tire well with master disconnect switch
(250)
Custom Chromoly Roll Cage with dash bar By Tim Bradham's Chassis Works.
(figure 2500)
Those are all low ballparks and that's over 14,000 in just parts. I'm sure I'm low on a lot of stuff too and that's not including any kind of installation besides installing the cage. It's definitly a great deal! People don't understand what it costs and how much time is involved in putting something like that together.
Good luck!
01-11-2006, 08:54 PM
#47
11 Second Club
Thread Starter
iTrader: (1)
Join Date: Sep 2003
Location: Fayettenam, North Cakalki
Posts: 1,252
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by LTLHOMER
13.5k for this car isn't bad at all. It's a real good price. You couldn't build it like that for less than 4-5 grand more than he's asking.
Thank You Sir!
Your Post above is about right on the price of the parts too.
Friday it's off the market. If I cannot get what I want for it, I may as well keep building it so it doesnt sit forever!
Thanks!!!
Brad
